Home » Seagate Manuals » Hard Drives » Seagate ST300MM0026 » Manual Viewer

Seagate ST300MM0026 Savvio 10K.2 SAS Product Manual - Page 29

Conducted noise immunity, Power sequencing, Current profiles

View all Seagate ST300MM0026 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

7.2.1 Conducted noise immunity Noise is specified as a periodic and random distribution of frequencies covering a band from DC to 10 MHz. Maximum allowed noise values given below are peak-to-peak measurements and apply at the drive power connector. +5v = 250 mV pp from 0 to 100 kHz to 20 MHz. +12v = 800 mV pp from 100 Hz to 8 KHz. 450 mV pp from 8 KHz to 20 KHz. 250 mV pp from 20 KHz to 5 MHz. 7.2.2 Power sequencing The drive does not require power sequencing. The drive protects against inadvertent writing during power-up and down. 7.2.3 Current profiles The +12V and +5V current profiles for the ST9146802SS and ST973402SS models are shown below. Figure 2. ST9146802SS current profile Savvio 10K.2 SAS Product Manual, Rev. E 23

Section	Page
1.0 Seagate Technology support services	7
2.0 Scope	8
3.0 Applicable standards and reference documentation	9
3.1 Standards	9
3.1.1 Electromagnetic compatibility	9
3.1.2 Electromagnetic compliance	10
3.1.3 European Union Restriction of Hazardous Substances (RoHS)	11
3.2 Reference documents	11
4.0 General description	12
4.1 Standard features	13
4.2 Media description	13
4.3 Performance	13
4.4 Reliability	14
4.5 Formatted capacities	14
4.6 Programmable drive capacity	14
4.7 Factory-installed accessories	14
4.8 Factory-installed options	15
5.0 Performance characteristics	16
5.1 Internal drive characteristics	16
5.2 Seek performance characteristics	16
5.2.1 Access time	16
5.2.2 Format command execution time for 512-byte sectors (minutes)	17
5.2.3 General performance characteristics	17
5.3 Start/stop time	17
5.4 Prefetch/multi-segmented cache control	18
5.5 Cache operation	18
5.5.1 Caching write data	18
5.5.2 Prefetch operation	19
6.0 Reliability specifications	20
6.1 Error rates	20
6.1.1 Recoverable Errors	20
6.1.2 Unrecoverable Errors	20
6.1.3 Seek errors	21
6.1.4 Interface errors	21
6.2 Reliability and service	21
6.2.1 Annualized Failure Rate (AFR) and Mean Time Between Failure (MTBF)	21
6.2.2 Preventive maintenance	21
6.2.3 Hot plugging the drive	21
6.2.4 S.M.A.R.T.	22
6.2.5 Thermal monitor	23
6.2.6 Drive Self Test (DST)	24
6.2.7 Product warranty	26
7.0 Physical/electrical specifications	27
7.1 AC power requirements	27
7.2 DC power requirements	27
7.2.1 Conducted noise immunity	29
7.2.2 Power sequencing	29
7.2.3 Current profiles	29
7.3 Power dissipation	31
7.4 Environmental limits	32
7.4.1 Temperature	32
7.4.2 Relative humidity	33
7.4.3 Effective altitude (sea level)	33
7.4.4 Shock and vibration	33
7.4.5 Air cleanliness	35
7.4.6 Corrosive environment	35
7.4.7 Acoustics	36
7.4.8 Electromagnetic susceptibility	36
7.5 Mechanical specifications	37
8.0 Defect and error management	38
8.1 Drive internal defects/errors	38
8.2 Drive error recovery procedures	38
8.3 SAS system errors	39
8.4 Background Media Scan	40
8.5 Media Pre-Scan	40
8.6 Deferred Auto-Reallocation	40
8.7 Idle Read After Write	41
9.0 Installation	42
9.1 Drive orientation	42
9.2 Cooling	43
9.3 Drive mounting	44
9.4 Grounding	44
10.0 Interface requirements	45
10.1 SAS features	45
10.1.1 task management functions	45
10.1.2 task management responses	45
10.2 Dual port support	46
10.3 SCSI commands supported	47
10.3.1 Inquiry data	51
10.3.2 Mode Sense data	51
10.4 Miscellaneous operating features and conditions	55
10.4.1 SAS physical interface	56
10.4.2 Physical characteristics	59
10.4.3 Connector requirements	59
10.4.4 Electrical description	59
10.4.5 Pin descriptions	59
10.4.6 SAS transmitters and receivers	60
10.4.7 Power	60
10.5 Signal characteristics	60
10.5.1 Ready LED Out	60
10.5.2 Differential signals	61
Numerics	71
A	71
B	71
C	71
D	71
E	71
F	72
G	72
H	72
I	72
J	72
L	72
M	72
N	73
O	73
P	73
Q	73
R	73
S	73
T	74
U	74
V	74
W	74