Seagate ST32000646SS Constellation ES.2 SAS Product Manual - Page 39

Constellation ES.2 SAS Product Manual, Rev. C

31

7.5.4.2

Vibration

a. Operating—normal

The drive as installed for normal operation, shall comply with the complete specified performance while

subjected to continuous vibration not exceeding

5 - 22 Hz

0.25 Gs, limited displacement

22 - 350 Hz

0.5 Gs

350 - 500 Hz

0.25 Gs

Vibration may be applied in the X, Y, or Z axis.

b. Operating—abnormal

Equipment as installed for normal operation shall not incur physical damage while subjected to periodic

vibration not exceeding:

15 minutes of duration at major resonant frequency

Vibration occurring at these levels may degrade operational performance during the abnormal vibration

period. Specified operational performance will continue when normal operating vibration levels are

resumed. This assumes system recovery routines are available.

Operating abnormal translational random flat profile

5-500 Hz @ 0.75 G (X, Y, or Z axis)

c. Non-operating

The limits of non-operating vibration shall apply to all conditions of handling and transportation. This

includes both isolated drives and integrated drives.

The drive shall not incur physical damage or degraded performance as a result of continuous vibration not

exceeding

5 - 22 Hz

2 Gs (0 to peak, linear, swept sine, 0.5 octave/min)

22 - 350 Hz


350 - 500 Hz


Vibration may be applied in the X, Y, or Z axis.

7.5.5

Acoustics

Sound power during idle mode shall be 2.8 bels typical when measured to ISO 7779 specification. Sound

power while operating shall be 3.0 bels typical when measured to ISO 7779 specification.

There will not be any discrete tones more than 10 dB above the masking noise on typical drives when

measured according to Seagate specification 30553-001. There will not be any tones more than 24 dB above

the masking noise on any drive.

7.5.6

Air cleanliness

The drive is designed to operate in a typical office environment with minimal environmental control.

7.5.7

Corrosive environment

Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to

light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM

B845. However, this accelerated testing cannot duplicate every potential application environment.

Users should use caution exposing any electronic components to uncontrolled chemical pollutants and

corrosive chemicals as electronic drive component reliability can be affected by the installation environment.

The silver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of

sulfide, chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic

Section	Page
1.0 Seagate Technology support services	9
2.0 Scope	10
3.0 Applicable standards and reference documentation	11
3.1 Standards	11
3.1.1 Electromagnetic compatibility	11
3.1.1.1 Electromagnetic susceptibility	11
3.1.2 Electromagnetic compliance	12
3.1.3 European Union Restriction of Hazardous Substances (RoHS)	13
3.1.4 China Restriction of Hazardous Substances (RoHS) Directive	13
3.2 Reference documents	14
4.0 General description	15
4.1 Standard features	16
4.2 Media description	16
4.3 Performance	16
4.4 Reliability	17
4.5 Formatted capacities	17
4.6 Programmable drive capacity	17
4.7 Factory-installed options	17
5.0 Performance characteristics	18
5.1 Internal drive characteristics	18
5.2 Seek performance characteristics	18
5.2.1 Access time	18
5.2.2 Format command execution time for 512-byte sectors (minutes)	19
5.2.3 General performance characteristics	19
5.3 Start/stop time	19
5.4 Prefetch/multi-segmented cache control	20
5.5 Cache operation	20
5.5.1 Caching write data	21
5.5.2 Prefetch operation	21
6.0 Reliability specifications	22
6.1 Error rates	22
6.1.1 Recoverable Errors	22
6.1.2 Unrecoverable Errors	22
6.1.3 Seek errors	23
6.1.4 Interface errors	23
6.2 Reliability and service	23
6.2.1 Annualized Failure Rate (AFR) and Mean Time Between Failure (MTBF)	23
6.2.2 Preventive maintenance	23
6.2.3 Hot plugging the drive	23
6.2.4 S.M.A.R.T.	24
6.2.5 Thermal monitor	25
6.2.6 Drive Self Test (DST)	26
6.2.6.1 DST failure definition	26
6.2.6.2 Implementation	26
6.2.7 Product warranty	28
7.0 Physical/electrical specifications	29
7.1 PowerChoiceTM power management	29
7.1.1 PowerChoice reporting methods	30
7.2 AC power requirements	30
7.3 DC power requirements	30
7.3.1 Conducted noise immunity	32
7.3.2 Power sequencing	32
7.3.3 Current profiles	33
7.4 Power dissipation	34
7.5 Environmental limits	36
7.5.1 Temperature	36
7.5.2 Relative humidity	36
7.5.3 Effective altitude (sea level)	37
7.5.4 Shock and vibration	37
7.5.4.1 Shock	37
7.5.4.2 Vibration	39
7.5.5 Acoustics	39
7.5.6 Air cleanliness	39
7.5.7 Corrosive environment	39
7.5.8 Electromagnetic susceptibility	40
7.6 Mechanical specifications	41
8.0 About FIPS	42
9.0 About self-encrypting drives	43
9.1 Data encryption	43
9.2 Controlled access	43
9.2.1 Admin SP	43
9.2.2 Locking SP	43
9.2.3 Default password	44
9.3 Random number generator (RNG)	44
9.4 Drive locking	44
9.5 Data bands	44
9.6 Cryptographic erase	44
9.7 Authenticated firmware download	45
9.8 Power requirements	45
9.9 Supported commands	45
9.10 RevertSP	45
10.0 Defect and error management	46
10.1 Drive internal defects/errors	46
10.2 Drive error recovery procedures	46
10.3 SAS system errors	47
10.4 Background Media Scan	47
10.5 Media Pre-Scan	48
10.6 Deferred Auto-Reallocation	48
10.7 Idle Read After Write	48
10.8 Protection Information (PI)	49
10.8.1 Levels of PI	49
10.8.2 Setting and determining the current Type Level	49
10.8.3 Identifying a Protection Information drive	49
11.0 Installation	50
11.1 Drive orientation	50
11.2 Cooling	51
11.3 Drive mounting	52
11.4 Grounding	52
12.0 Interface requirements	53
12.1 SAS features	53
12.1.1 task management functions	53
12.1.2 task management responses	53
12.2 Dual port support	54
12.3 SCSI commands supported	55
12.3.1 Inquiry data	59
12.3.2 Mode Sense data	59
12.4 Miscellaneous operating features and conditions	62
12.4.1 SAS physical interface	63
12.4.2 Physical characteristics	66
12.4.3 Connector requirements	66
12.4.4 Electrical description	66
12.4.5 Pin descriptions	66
12.4.6 SAS transmitters and receivers	67
12.4.7 Power	67
12.5 Signal characteristics	67
12.5.1 Ready LED Out	67
12.5.2 Differential signals	68
12.6 SAS-2 Specification Compliance	68
12.7 Additional information	68
Numerics	69
A	69
B	69
C	69
D	69
E	70
F	70
G	70
H	70
I	70
J	70
K	70
L	71
M	71
N	71
O	71
P	71
Q	72
R	72
S	72
T	72
U	73
V	73
W	73

Seagate ST32000646SS Constellation ES.2 SAS Product Manual - Page 39

Vibration, Acoustics, Air cleanliness, Corrosive environment

Page 39 highlights