Home » Seagate Manuals » Hard Drives » Seagate ST3300657SS » Manual Viewer

Seagate ST3300657SS Cheetah 15K.7 FC Product Manual - Page 15

Performance characteristics - sector size

UPC - 715663214328

View all Seagate ST3300657SS manuals

Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

4.0 Performance characteristics This section provides detailed information concerning performance-related characteristics and features of Cheetah 15K.7 FC drives. 4.1 Internal drive characteristics Drive capacity Read/write data heads Tracks per inch Peak bits per inch Areal Density Internal data rate disk rotation speed Avg rotational latency ST3600057FC ST3600957FC 600 8 165,000 1,361 225 1.49 - 2.37 15k 2.0 ST3450857FC ST3450757FC 450 6 165,000 1,361 225 1.49 - 2.37 15k 2.0 ST3300657FC ST3300557FC 300 4 165,000 1,361 225 1.49 - 2.37 15k 2.0 Gbytes (formatted, rounded off value)* TPI KBPI Gbits/inch2 Gbits/sec (max) RPM msec *One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. 4.2 Seek performance characteristics See Section 10.5, "FC-AL physical interface" on page 63 and the Fibre Channel Interface Manual (part number 77767496) for additional timing details. 4.2.1 Access time Average Single track Full stroke Typical Typical Typical Not including controller overhead1,2(msec) Read Write 3.4 3.9 0.2 0.44 6.6 7.4 1. Typical access times are measured under nominal conditions of temperature, voltage, and horizontal orientation as measured on a representative sample of drives. 2. Access to data = access time + latency time. 4.2.2 Format command execution time (minutes) When changing sector sizes, the format times shown below may need to be increased by 30 minutes. Maximum (with verify) Maximum (without verify) ST3600057FC 119 60 ST3450857FC 88 44 ST3300657FC 58 29 Note. There is approximately a 1.5 increase in time to format a SED drive versus a non-SED drive of the same capacity. Cheetah 15K.7 FC Product Manual, Rev. B 9

Section	Page
1.0 Scope	7
2.0 Applicable standards and reference documentation	8
2.1 Standards	8
2.1.1 Electromagnetic compatibility	8
2.1.1.1 Electromagnetic susceptibility	8
2.1.2 Electromagnetic compliance	9
2.2 European Union Restriction of Hazardous Substances (RoHS)	9
2.3 Reference documents	10
3.0 General description	11
3.1 Standard features	12
3.2 Media description	13
3.3 Performance	13
3.4 Reliability	13
3.5 Formatted capacities	13
3.5.1 Programmable drive capacity	14
3.6 Factory-installed options	14
3.7 User-installed accessories	14
4.0 Performance characteristics	15
4.1 Internal drive characteristics	15
4.2 Seek performance characteristics	15
4.2.1 Access time	15
4.2.2 Format command execution time (minutes)	15
4.2.3 General performance characteristics	16
4.3 Start/stop time	16
4.4 Prefetch/multi-segmented cache control	16
4.5 Cache operation	17
4.5.1 Caching write data	17
4.5.2 Prefetch operation	18
5.0 Reliability specifications	19
5.1 Error rates	19
5.1.1 Recoverable Errors	19
5.1.2 Unrecoverable Errors	19
5.1.3 Seek errors	20
5.1.4 Interface errors	20
5.2 Reliability and service	20
5.2.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF)	20
5.2.2 Preventive maintenance	20
5.2.3 Hot plugging the drive	20
5.2.4 S.M.A.R.T.	21
5.2.5 Thermal monitor	22
5.2.6 Drive Self Test (DST)	23
5.2.6.1 DST failure definition	23
5.2.6.2 Implementation	23
5.2.7 Product warranty	25
6.0 Physical/electrical specifications	26
6.1 AC power requirements	26
6.2 DC power requirements	26
6.2.1 Conducted noise immunity	29
6.2.2 Power sequencing	29
6.2.3 Current profiles	29
6.3 Power dissipation	32
6.4 Environmental limits	34
6.4.1 Temperature	34
6.4.2 Relative humidity	35
6.4.3 Effective altitude (sea level)	35
6.4.4 Shock and vibration	36
6.4.4.1 Shock	36
6.4.4.2 Vibration	38
6.4.5 Acoustics	38
6.4.6 Air cleanliness	38
6.4.7 Corrosive environment	38
6.4.8 RoHS compliance statement	39
6.4.9 Electromagnetic susceptibility	39
6.5 Mechanical specifications	40
7.0 About self-encrypting drives	41
7.1 Data encryption	41
7.2 Controlled access	41
7.2.1 Admin SP	41
7.2.2 Locking SP	42
7.2.3 Default password	42
7.3 Random number generator (RNG)	42
7.4 Drive locking	42
7.5 Data bands	42
7.6 Cryptographic erase	43
7.7 Authenticated firmware download	43
7.8 Power requirements	43
7.9 Supported commands	43
8.0 Defect and error management	44
8.1 Drive internal defects/errors	44
8.2 Drive error recovery procedures	44
8.3 FC-AL system errors	46
8.4 Background Media Scan	47
8.5 Media Pre-Scan	47
8.6 Deferred Auto-Reallocation	47
8.7 Idle Read After Write	48
9.0 Installation	49
9.1 Drive ID/option selection	49
9.2 Drive orientation	49
9.3 Cooling	50
9.4 Drive mounting	51
9.5 Grounding	51
10.0 Interface requirements	52
10.1 FC-AL features	52
10.1.1 Fibre Channel link service frames	52
10.1.2 Fibre Channel task management functions	53
10.1.3 Fibre Channel task management responses	53
10.1.4 Fibre Channel port login	54
10.1.5 Fibre Channel port login accept	55
10.1.6 Fibre Channel Process Login	55
10.1.7 Fibre Channel Process Login Accept	56
10.1.8 Fibre Channel fabric login	56
10.1.9 Fibre Channel fabric accept login	57
10.1.10 Fibre Channel Arbitrated Loop options	58
10.2 Dual port support	58
10.3 SCSI commands supported	58
10.3.1 Inquiry data	63
10.3.2 Mode Sense data	63
10.4 Miscellaneous operating features and conditions	68
10.5 FC-AL physical interface	69
10.5.1 Physical characteristics	69
10.5.1.1 Physical description	69
10.5.2 Connector requirements	70
10.5.3 Electrical description	70
10.5.4 Pin descriptions	70
10.5.5 FC-AL transmitters and receivers	71
10.5.6 Power	72
10.5.7 Fault LED Out	72
10.5.8 Active LED Out	73
10.5.9 Enable port bypass signals	73
10.5.10 Motor start controls	73
10.5.11 SEL_6 through SEL_0 ID lines	74
10.5.11.1 Parallel Enclosure Services Interface (ESI)	74
10.5.12 Device control codes	76
10.6 Signal characteristics	76
10.6.1 TTL input characteristics	76
10.6.2 LED driver signals	77
10.6.3 FC Differential output	77
10.6.4 FC Differential input	77