Seagate ST373207FC Cheetah 10K.7 FC Product Manual

Seagate ST373207FC - Cheetah 73 GB Hard Drive Manual

Get Seagate ST373207FC - Cheetah 73 GB Hard Drive PDF manuals and user guides
UPC - 000056439373
View all Seagate ST373207FC manuals
Add to My Manuals
Save this manual to your list of manuals

Seagate ST373207FC manual content summary:

  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 1
    Users Guide Cheetah 10K.7 FC ST3300007FC ST3146707FC ST373207FC
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 2
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 3
    Users Guide Cheetah 10K.7 FC ST3300007FC ST3146707FC ST373207FC
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 4
    Publication number: 100260916, Rev. D July 2005 Seagate and Seagate Technology are registered trademarks of Seagate Technology LLC. Cheetah, SeaTools, SeaFONE, SeaBOARD, SeaTDD, and the Wave logo are either registered trademarks or trademarks of Seagate Technology LLC. Other product names are
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 5
    Revision Rev. A Rev. B Rev. C Rev. D Revision status summary sheet Date 03/17/04 09/22/04 05/05/05 07/26/05 Sheets Affected 1/1, v-viii, 1-83. Pages 9, 12, 17, 18, 25, 26, 28-34, 37, 40, 41, 59, and 77-80. Pages 8, 11, 12, 17, 37, 52, 53, 58, and 77-81. Pages 4, 12, 26, and 79-83.
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 6
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 7
    errors 18 5.2 Reliability and service 18 5.2.1 Annualized Failure Rate (AFR 18 5.2.2 Preventive maintenance 18 5.2.3 Hot plugging the drive 19 5.2.4 S.M.A.R.T 19 5.2.5 Thermal monitor 20 5.2.6 Drive Self Test (DST 21 5.2.7 Product warranty 23 Cheetah 10K.7 FC Product Manual, Rev. D v
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 8
    9.1.9 Fibre Channel fabric accept login 54 9.1.10 Fibre Channel Arbitrated Loop options 55 9.2 Dual port support 55 9.3 SCSI commands supported 56 9.3.1 Inquiry data 61 9.3.2 Mode Sense data 61 9.4 Miscellaneous operating features and conditions 66 vi Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 9
    ID lines 73 9.5.12 Device control codes 75 9.6 Signal characteristics 75 9.6.1 TTL input characteristics 75 9.6.2 LED driver signals 76 9.6.3 Differential PECL output 76 9.6.4 Differential PECL input 76 10.0 Seagate Technology support services 79 Cheetah 10K.7 FC Product Manual, Rev. D vii
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 10
    viii Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 11
    Cheetah 10K.7 FC family disc drive 1 Typical ST3300007FC drive, 2 Gbit, +12V current profile 28 Typical ST3300007FC drive, 2 Gbit, +5V current profile 28 Typical ST3146707FC drive, 2 Gbit, +12V current profile 29 Typical ST3146707FC drive, 2 Gbit, +5V current profile 29 Typical ST373207FC drive
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 12
    x Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 13
    Scope This manual describes Seagate Technology® LLC, Cheetah® 10K.7 FC (Fibre Channel) disc drives. Cheetah 10K.7 FC drives support the Fibre Channel Arbitrated Loop and SCSI Fibre Channel Protocol specifications to the extent described in this manual. The Fibre Channel Interface Manual (part number
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 14
    2 Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 15
    Cheetah 10K.7 FC family complies with Seagate standards as noted in the appropriate sections of this manual and the Seagate Fibre Channel Interface Manual, part number 77767496. The Cheetah 10K.7 FC disc drive shielding. If the I/O cables are external to the enclosure, shielded cables should be
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 16
    inch floppy disc drive • Keyboard • Monitor/display • Printer • External modem • Mouse Although the test system with this Seagate model complies with July 2006. The directive's requirements have not been finalized. This drive is manufactured with components and materials that are expected to comply
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 17
    Reference documents Cheetah 10K.7 FC Installation Guide Seagate part number: 100260920 Fibre Channel Interface Manual Seagate part number: Selection Specification for 40-pin SCA-2 Connector with Bidirectional Enclosure Services Interface ANSI Small Computer System Interface (SCSI) Documents X3.
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 18
    6 Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 19
    drives support the Fibre Channel Arbitrated Loop (FC-AL) and SCSI Fibre Channel Protocol as described in the ANSI specifications, this document, and the Fibre Channel Interface Manual (part number 77767496) which describes the general interface characteristics of this drive. Cheetah 10K.7 FC drives
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 20
    public attachment • Differential copper FC drivers and receivers • Downloadable firmware using the FC-AL interface • Supports SCSI enclosure services via interface connector • 128-deep task set (queue) • Supports up to 32 initiators • Drive selection ID and configuration options are set on the FC-AL
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 21
    Background processing of queue • Supports start and stop commands 3.4 Seagate recommends product planning in one of two modes: 1. Seagate designs specify capacity points at certain sector sizes that Seagate 21FA5188 21BC97F8 21407E5A 2. Seagate drives also may be used at Using the drives in this
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 22
    Manual. Refer to the Parameter list block descriptor number of blocks field. A value of zero in the number of blocks field indicates that the drive 3.6 Factory-installed accessories OEM standard drives are shipped with the Cheetah 10K.7 FC Installation Guide (part number 100260920). 3.7 Factory
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 23
    related characteristics and features of Cheetah 10K.7 FC drives. 4.1 Internal drive characteristics ST3300007FC ST3146707FC ST373207FC Drive capacity 300.0 146.8 73 10,000 10,000 ....... rpm (+ 0.5%) Avg rotational latency 3.0 3.0 3.0 msec Cheetah 10K.7 FC Product Manual, Rev. D 11
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 24
    overhead (without disconnect) [1] (ST3300007 data shown) Drive level Read Write msec 4.9 5.4 0.45 0.65 without verify) ST3300007FC 200 100 ST3146707FC 100 50 ST373207FC 50 25 4.2.3 Generalized performance characteristics Minimum sector Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 25
    representative sample of drives. [3] Assumes system ability to support the rates drive, 6,991 kbytes can be used as a cache. The buffer can be divided into logical segments (using Mode Select Page 08h, byte 13) from which data is read and to which data is written. Cheetah 10K.7 FC Product Manual
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 26
    a wide range of user-selectable configurations. The drive supports operation of any integer number of segments from space and segmentation is used as set up for read functions. The buffer segmentation scheme is set up or changed independently, having nothing Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 27
    will have been written to the medium. Table 27 shows the mode default settings for the drive. 4.5.2 Prefetch operation If the Prefetch feature is enabled, data in contiguous (1Ah) in the Fibre Channel Interface Product Manual, part number 77767496. Cheetah 10K.7 FC Product Manual, Rev. D 15
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 28
    16 Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 29
    AFR 0.62% Service life Preventive drive is operated in accordance with this manual using DC power as defined in paragraph 6.2, "DC power requirements." • Errors caused by host system failures are excluded from error rate computations. • Assume random data. • Default OEM error recovery settings
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 30
    loop of devices is the sum of the individual device error rates. 5.2 Reliability and service You can enhance the reliability of Cheetah 10K.7 SCSI disc drives by ensuring that the drive receives adequate cooling. Section 6.0 provides temperature measurements and other information that may be used
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 31
    port bypass circuit (external to the drive), defaults to the Enable drive's firmware monitors specific attributes for degradation over time but can't predict instantaneous drive failures. Each monitored attribute has been selected to monitor a specific set Cheetah 10K.7 FC Product Manual, Rev. D 19
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 32
    Subject to the reporting method, the firmware will issue to the host an drive temperature and issues a warning over the interface when the temperature exceeds a set threshold. The temperature is measured at power-up and then at ten-minute intervals after power-up. 20 Cheetah 10K.7 FC Product Manual
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 33
    page (see Table 1) can be used to set this trip point. The default value for this drive is 68°C, however, you can set it to any value in the range of 0 condition. If the drive fails the test, remove it from service and return it to Seagate for service. Cheetah 10K.7 FC Product Manual, Rev. D 21
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 34
    of DST, a Not Ready condition also qualifies the drive to be returned to Seagate as a failed drive. A Drive Not Ready condition is reported by the drive under the following conditions: • Motor will not spin test segment, and a read/verify scan segment. 22 Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 35
    procedure. Seagate will pay for transporting the repair or replacement item to the customer. For more detailed warranty information, refer to the standard terms and conditions of purchase for Seagate products. Refer to Section 10 for contact information. Cheetah 10K.7 FC Product Manual, Rev
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 36
    return information Seagate customer service centers are the only facilities authorized to service Seagate drives. Seagate does not sanction any third-party repair facilities. Any unauthorized repair or tampering with the factory seal voids the warranty. 24 Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 37
    The voltage and current requirements for a single drive are shown below. Values indicated apply at the drive connector. Table 11: ST3300007FC DC power requirements [2] ±5% [2] 0.63 1.08 1.97 1.40 4.04 0.61 0.09 0.96 1.10 0.96 1.11 1.80 2.72 Cheetah 10K.7 FC Product Manual, Rev. D 25
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 38
    1.46 3.96 0.62 0.09 0.94 0.91 0.97 0.92 1.78 2.54 Table 13: ST373207FC DC power requirements Notes Voltage Regulation [5] Avg idle current DC X [1] [7] Maximum starting current (peak . Number of drives tested = 6, 35 Degrees C ambient. 26 Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 39
    allowed noise values given below are peak to peak measurements and apply at the drive power connector. +5 V = +12 V = 250 mV pp from 100 Hz drive does not require power sequencing. The drive protects against inadvertent writing during power-up and down. Cheetah 10K.7 FC Product Manual, Rev. D 27
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 40
    the various times is as shown: Note: All times and currents are typical. See Table 11 for maximum current requirements. Figure 2. Typical ST3300007FC drive, 2 Gbit, +12V current profile Figure 3. Typical ST3300007FC drive, 2 Gbit, +5V current profile 28 Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 41
    Figure 4. Typical ST3146707FC drive, 2 Gbit, +12V current profile Figure 5. Typical ST3146707FC drive, 2 Gbit, +5V current profile Cheetah 10K.7 FC Product Manual, Rev. D 29
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 42
    Figure 6. Typical ST373207FC drive, 2 Gbit, +12V current profile Figure 7. Typical ST373207FC drive, 2 Gbite, +5V current profile 30 Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 43
    refer to the following I/O rate curve (see Figure 8). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5 volt current, +12 volt ST3300007FC DC current and power vs. input/output operations per second Cheetah 10K.7 FC Product Manual, Rev. D 31
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 44
    refer to the following I/O rate curve (see Figure 8). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5 volt current, +12 volt ST3146707FC DC current and power vs. input/output operations per second 32 Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 45
    I/O rate curve (see Figure 8). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5 volt 5Volt A 12 Vo lt A Watts Figure 10. ST373207FC DC current and power vs. input/output operations per second Cheetah 10K.7 FC Product Manual, Rev. D 33
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 46
    (20°C) per hour. This specification assumes that the drive is packaged in the shipping container designed by Seagate for use with drive. HDA Temp. Check Point 1.0" .5" Figure 11. Location Non-operating -1,000 to +40,000 feet (-305 to +12,210 meters) 34 Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 47
    to 18.1 kg) 36 in (914 mm) Drives packaged in single or multipacks with a gross weight of 20 pounds (8.95 kg) or less by Seagate for general freight shipment shall withstand a drop test from 48 inches (1,070 mm) against a concrete floor or equivalent. Cheetah 10K.7 FC Product Manual, Rev. D 35
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 48
    Z Y X X Z Y Figure 12. Recommended mounting 36 Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 49
    office environment with minimal environmental control. 6.4.6 Corrosive environment Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure replacing materials near circuitry with sulfide-free alternatives. Cheetah 10K.7 FC Product Manual, Rev. D 37
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 50
    on typical drives when measured according to Seagate specification 30553-001. There will not be any tones more than 24 dB above the masking noise on any drive mounting configuration dimensions. See Section 8.5, "Drive mounting." Height: Width: Depth: Weight:
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 51
    32 UNC 2B, three on each side and four on the bottom. Max screw penetration into side of drive is 0.15 in. (3.81 mm). Max screw tightening torque is 6.0 in-lb (3.32 nm) with 0.38 max U .015 max 0.38 max E D Figure 13. Mounting configuration dimensions Cheetah 10K.7 FC Product Manual, Rev. D 39
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 52
    40 Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 53
    Manual. The drive implements selectable error recovery time limits required in video applications. The error recovery scheme supported by the drive Write Retry Count bytes in the Error Recovery mode page. The drive firmware error recovery algorithms consists of 12 levels for read recoveries and
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 54
    . Therefore, each command's total recovery time is subject to the recovery time limit. Note: A recovery time limit of 0 will use the drive's default value of FF FF. Minimum recovery time limit is achieved by setting the Recovery Time Limit field to 00 01. 42 Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 55
    service by the host system. On regualr duty drives, if the host system makes use of the BGMS Log Page, it can avoid placing data in suspect locations on the media. Unrecovered error sites found during BGMS will be logged and recovered error sites will be logged or reallocated per ARRE/AWRE settings
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 56
    44 Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 57
    reformat the drive only if you want to select a different logical block size. 8.1 Drive ID/option selection All drive options are made through the interface connector (J1). Table provides the pin descriptions for the 40pin Fibre Channel single connector (J1). Cheetah 10K.7 FC Product Manual, Rev
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 58
    Active LED [1] Ground [3] [1] The drive has a 1.2K ohm resistor in series with this LED driver. Tie the minus side of an external high-efficiency LED (i.e., 2ma) to this [3] Jumper storage location (across pins 2 and 4). Figure 15. LED indicator connector 46 Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 59
    8.3 Drive orientation The drive may be mounted in any orientation. All drive performance characterizations, however, have been done with the drive in horizontal (discs level) and vertical (drive on to side) Figure 16. Air flow Above unit Under unit Cheetah 10K.7 FC Product Manual, Rev. D 47
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 60
    drive in any kind of 3.5-inch to 5.25-inch adapter frame, verify with Seagate Technology that the drive manual. 8.6 Grounding Signal ground (PCBA) and HDA ground are connected together in the drive and cannot be separated by the user. The equipment in which the drive of mounting the drive in the
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 61
    Manual (part number 77767496). 9.1 FC-AL features This section lists the Fibre Channel-specific features supported by Cheetah 10K.7 FC drives. 9.1.1 Fibre Channel link service frames Table 15 lists the link services supported by Cheetah 10K.7 FC drives. Table 15: Link services supported
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 62
    Terminate task Clear ACA Target reset Clear task set Abort task set Supported No No Yes Yes Yes 9.1.3 Fibre Channel supported. Table 17: FC SCSI FCP response codes Function name Function complete Function not supported Function reject Response code 00 04 05 50 Cheetah 10K.7 FC Product Manual
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 63
    Not checked. Port Login Accept will return a 0-not supported. Valid version level x N_Port/F_Port Must = 0, N_Port name. The node name is not checked or saved by the drive. SO Service options Class 3 only. MSB Class valid Must = 1 Intermix than 0. Cheetah 10K.7 FC Product Manual, Rev. D 51
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 64
    23 and 24) and (30, 31 and 32) are currently factory set to 00 04 CF respectively (subject to change). FS Receive buffer field size. The drive returns and uses the receive buffer size from the N_Port Login Class 22 XX Indicates fields that are not used. 52 Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 65
    (subject to change). UI Unique identifier. This 24-bit field is uniquely assigned to the drive. This same UI appears in the Port Name and Node Name fields. PP Port identifier field. 01 FLOGI originated on Port A. 02 FLOGI originated on Port B. Cheetah 10K.7 FC Product Manual, Rev. D 53
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 66
    is returned to the fabric. NN Node Name. The drive does not check or save the node name. SO Service Options-Class 3 only. MSB Class valid Must = 1 Intermix x Stacked connection req. xx Sequential delivery Must = 1 Other bits reserved xxx XX 54 Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 67
    ) the connection of Port A and B for these products must follow the requirements in their product manuals. Subject to buffer availability, the Cheetah 10K.7 FC drives support: • Concurrent port transfers-The drive supports receiving transfers on both ports at the same time when the ports are on
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 68
    Y Firmware numbers page (C0h) Y Date code page (C1h) Y Jumper settings page (C2h) Y Device behavior page (C3h) Y Mode select (same pages as Mode Sense command shown below) [3] Y Reserve N 3rd party reserved N Extent reservation Y Release N Copy 56 Cheetah 10K.7 FC Product Manual
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 69
    Y Enclosure services page 1Dh Y Send diagnostics page Y Supported diagnostics pages Y Translate page 25h Y Read capacity 28h Y Read extended Y Disable page out Y Force unit access N Relative address 2Ah Y Write extended Y Disable page out Y Force unit access Cheetah 10K
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 70
    continued) Command code 2Bh 2Eh Supported [4] Command name N Relative address N Search data equal 32h N Search data low 33h N Set limits 34h N Prefetch 35h Y Synchronize cache 36h N Lock and save mode (7) Y Firmware download option [2] 58 Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 71
    4Ch 4Dh Y Write same N PBdata N LBdata N Not used Y Log Select Y Log Sense Y Supported Log page (00h) Y Write Error Counter page (02h) Y Read Error Counter page (03h) 4E N Not used 50h N XD write 51h N XP write 52h N XD read Cheetah 10K.7 FC Product Manual, Rev. D 59
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 72
    can result in firmware corruption. This usually makes the drive inoperable. [3] Reference Mode Sense command 1Ah for mode pages supported. [4] Y = Yes. Command is supported. N = No. Command is not supported. A = Support is available on special request. 60 Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 73
    43 ST373207FC 33 37 33 32 30 37 46 43 20 9.3.2 Mode Sense data The Mode Sense command provides a way for the drive to report its operating parameters to the initiator. The drive maintains four sets of mode parameters: 1. Default values Default values are hard-coded in the drive firmware stored
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 74
    by the drive in response to the Mode Sense command pages for SCSI implementation (see the Fibre Channel Interface Manual). Definitions: DEF = Default value. Standard OEM drives are shipped configured this way. CHG = Changeable bits; indicates if default value is changeable. 62 Cheetah 10K.7 FC
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 75
    Table 27: Mode Sense data default and changeable values for ST3300007FC drives ST3300007FC Bytes 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 00 0f 00 00 00 80 06 b7 40 0f 00 00 00 22 ec b2 5b 00 00 02 00 Cheetah 10K.7 FC Product Manual, Rev. D 63
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 76
    Table 28: Mode Sense data default and changeable values for ST3146707FC drives ST3146707FC Bytes 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 0f 00 00 00 CHG 80 06 b7 40 0f 00 00 00 11 17 73 2f 00 00 02 00 64 Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 77
    Table 29: Mode Sense data default and changeable values for ST3146707FC drives ST373207FC Bytes 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 00 00 00 CHG 80 06 b7 40 0f 00 00 00 08 8b b9 97 00 00 02 00 Cheetah 10K.7 FC Product Manual, Rev. D 65
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 78
    bytes Table 31: Miscellaneous status Supported Y Y Y Y Y Y Y Status Good Check condition Condition met/good Busy Intermediate/good Intermediate/condition met/good Reservation conflict Y Task set full N ACA active N ACA active, faulted initiator 66 Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 79
    The operational aspects of Seagate's Fibre Channel drives are provided in the Fibre Channel Interface Manual. J6 Figure 17. the loop with loop operation recovery after a brief interruption. These PBCs are located external to the FC-AL device. Figure 18 shows the relationship between the PBC and
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 80
    point of contact) 0.060 ± .010 in (1.52 ± 0.25 mm) 0.051 ± .006 in 2 places (1.30 ± 0.16 mm) Figure 19. FC-AL SCA device connector dimensions 68 Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 81
    Channel drives use the FC-SCA connector for: • DC power • FC-AL interface • Drive select (device identification) • Option selection • Enclosure Services interface This 40-pin connector is designed to plug directly into a backpanel. External cables are not required. Cheetah 10K.7 FC Product Manual
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 82
    open or grounded (open for the '1' setting, grounded for the '0' setting). Alternatively, these pins may be driven by a 3.3V logic device, pulled up to 3.3V through a pull-up resistor (recommended size of 10K ohm), or grounded through some other means. 70 Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 83
    9.5.6 Power Power is supplied through the FC-SCA with support for +5 volts and +12 volts. All of the voltage pins in the drive connector are the same length. Four 12 volt pins provide LED and the current-limiting resistor are external to the drive. Cheetah 10K.7 FC Product Manual, Rev. D 71
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 84
    and the current limiting resistor are external to the drive. 9.5.9 Enable port bypass signals drive that will enable bypass include: • Transmitter/receiver wrap test failure • Loss of receive clock • Loss of transmission clock • Drive interface hardware error 72 Cheetah 10K.7 FC Product Manual
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 85
    indicates the drive is attempting an ESI transfer. The enclosure may not support ESI on any or all drive locations. It may only support the address function. Support of ESI is discovered by the drive. Refer to the Fibre Channel Interface Manual for a description of ESI operations. Cheetah 10K.7 FC
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 86
    16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 Setting (dec) 00 01 02 03 04 05 06 07 08 09 10 11 12 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F Setting (dec) 43 44 45 46 47 48 49 50 51 52 53 54 55 6C 6D 6E 6F 70 71 72 73 74 75 76 77 78 79 7A Setting (dec) 86 87 88 89 90 91 92 93 94 95 96 97 98
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 87
    not connect to these lines, the drive has 10K ohm pull up resistors that default the device control code to 7 (1.0625 GHz). Table 36 lists the supported codes. Table 36: Device control code IOH < -500µA IOL < 2.4mA IOH < -1.6mA IOH < -500µA IOL < 1.6mA Cheetah 10K.7 FC Product Manual, Rev. D 75
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 88
    9.6.2 LED driver signals Fault and Active LED signals are located in the FC-SCA connector (J1) and through the indicator connector (J6). See Table 38 for the output characteristics of the LED drive signals. Table 38: LED drive signal State LED off, high LED on, low Current drive available 0 <
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 89
    and minimum requirements to recover data at the specified interface error rate. The inputs are AC coupled on the drive. Table 41 lists the data values. Bit Time Vin (mv) RCV Eye (typical) (minimum) Figure 23 ps 2 GHz 470 ps 315 ps min. 305 ps 226 ps Cheetah 10K.7 FC Product Manual, Rev. D 77
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 90
    78 Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 91
    If you need help installing your drive, consult your system's documentation or contact the dealer's support services department for assistance specific to your system. Seagate technical support is also available to assist you online at support.seagate.com or through one of our call centers. Have
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 92
    Customer Service Operations Warranty Service Seagate offers worldwide customer support for Seagate drives. Seagate distributors, OEMs and other direct customers should contact their Seagate Customer Service Operations (CSO) representative for warrantyrelated issues. Resellers or end users of drive
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 93
    to 5:00 P.M. (Central Europe time) Monday through Friday. The CSO warranty center is located in Amsterdam, The Netherlands. Seagate Service Centers Toll-free support numbers Call center Austria Belgium Denmark France Germany Ireland Italy Netherlands Norway Poland Spain Sweden Switzerland Turkey
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 94
    listed here, direct dial one of our technical support locations. Warranty service is available from 9:00 A.M. to 6:00 March (Australian Eastern time) Monday through Friday. Seagate Service Centers Call center Australia China (Mandarin)1, 4 Service Center 82 Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 95
    are interested in your comments and suggestions regarding this publication. Please take a few minutes to participate in our survey at the following URL: http://survey.seagate.com/survey/techpubs.nsf Thank you for your time and comments. Cheetah 10K.7 FC Product Manual, Rev. D 83
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 96
    84 Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 97
    basic link service frames 49 Basic_Accept (BA_ACC) 49 Basic_Reject (BA_RJT) 49 Cheetah 10K.7 FC Product Manual, Rev Communications 3 capacity unformatted 11 capacity, drive, programmable 9 CC 52, 53 50 clear task set function 50 command descriptor block (CDB) 13 commands supported 56 Common features
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 98
    drive capacity programmable 9 drive characteristics 11 drive failure 18 drive fault LED connection 46 drive ID 45 drive ID/option select headers 45 drive malfunction 18 drive mounting 38, 48 drive orientation 47 drive select 69 driver signals 76 drivers and receivers 8 dual port support link service
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 99
    internal defects/errors 41 internal drive characteristics 11 J J1 connector 45 J6 connector 46, 47 Jumper settings page command 56 jumpers 45 L latency average rotational 11, 13 LBdata 59 LED driver signals 76 link rate 75 Link Service Reject (LS_RJT) 49 link services supported 49 Lock-unlock-cache
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 100
    spindle operation 66 Zero latency read 66 miscellaneous status support ACA active 66 ACA active, faulted initiator 66 Busy /condition met/good 66 Intermediate/good 66 Reservation conflict 66 Task set full 66 miscorrected media data 17 Mode select (10) command Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 101
    10) command 60 reliability 9 specifications 17 reliability and service 18 repair and return information 24 reporting actual retry drive geometry page command 57 rotation speed 11 running disparity 19 S safety 3 SCA part numbers 68 SCSI interface commands supported 56 SCSI Interface Product Manual
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 102
    50 Function not supported 05 50 Function reject 04 50 task set full status 66 technical support services 79 temperature 13 page command 57 transmit eye diagram 76 transmitters 71 transporting the drive 24 TTL input characteristics 75 typical access time 13 U UI Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 103
    XP write 59 Z zero latency read 66 zone bit recording (ZBR) 8 Cheetah 10K.7 FC Product Manual, Rev. D 91
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 104
    92 Cheetah 10K.7 FC Product Manual, Rev. D
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 105
  • Seagate ST373207FC | Cheetah 10K.7 FC Product Manual - Page 106
    Seagate Technology LLC 920 Disc Drive, Scotts Valley, California 95066-4544, USA Publication Number: 100260916, Rev. D, Printed in USA
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Cheetah 10K.7 FC
ST3300007FC
ST3146707FC
ST373207FC