Home » Seagate Manuals » Hard Drives » Seagate ST9320320AS » Manual Viewer

Seagate ST9320320AS Momentus 5400.5 SATA Product Manual - Page 11

Drive specifications - ata cache

UPC - 890552607464

View all Seagate ST9320320AS manuals

Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the ST9320320AS, ST9250320AS, ST9200321AS, ST9160310AS, ST9160310ASG, ST9120310AS, ST9120310ASG, ST980310AS and ST980310ASG models. 2.1 Specification summary table The specifications listed in this table are for quick reference. For details on specification measurement or definition, see the appropriate section of this manual. Table 1: Drive specifications Drive specification ST9320320AS ST9250320AS ST9200321AS Formatted Gbytes (512 bytes/sector)* 320 250 200 Guaranteed sectors 625,142,448 488,397,168 390,721,968 Bytes per sector 512 Physical read/write heads 4 4 or 3 3 Discs 2 2 2 Cache (Mbytes) 8 Recording density in BPI (bits/inch avg) 1,337k Track density TPI (tracks/inch avg) 190k Areal density (Gbits/inch2 avg) 254 Spindle speed (RPM) 5,400 Average latency (msec) 5.6 Internal transfer rate 830 (Mbits/sec max) I/O data transfer rate 300 (Mbytes/sec max) ATA data-transfer modes supported SATA 1.0, Serial ATA Revision 2.6 PIO modes 0-4 Multiword DMA modes 0-2 Ultra DMA modes 0-6 Height (max) 9.5 +/- 0.2 mm (0.374 +/- .0078 inches) Width (max) 69.85 mm (2.75 +/- 0.0098 inches) Length (max) 100.5 +/- 0.25 mm (3.957 +/- 0.010 inches) Weight (max) 98.8 grams (0.218 lb) Power-on to ready (sec typical) 3.4 Standby to ready (sec typical) 3.2 ST9160310AS ST9120310AS ST980310AS ST9160310ASG ST9120310ASG ST980310ASG 160 120 80 312,581,808 234,441,648 156,301,488 2 2 1 1 1 1 93.5 grams (0.206 lb) Momentus 5400.5 SATA Product Manual, Rev. B 3

Section	Page
1.0 Introduction 1	5
1.1 About the Serial ATA interface 2	5
2.0 Drive specifications 3	5
2.1 Specification summary table 3	5
2.2 Formatted capacity 5	5
2.2.1 LBA mode 5	5
2.3 Default logical geometry 5	5
2.4 Physical organization 6	5
2.5 Recording and interface technology 6	5
2.6 Physical characteristics 6	5
2.7 Seek time 7	5
2.8 Start/stop times 7	5
2.9 Power specifications 8	5
2.9.1 Power consumption 8	5
2.9.2 Deferred spinup 9	5
2.9.3 Conducted noise 9	5
2.9.4 Voltage tolerance 9	5
2.9.5 Power-management modes 10	5
2.10 Environmental specifications 10	5
2.10.1 Ambient temperature 10	5
2.10.2 Temperature gradient 11	5
2.10.3 Humidity 11	5
2.10.4 Altitude 11	5
2.10.5 Shock 12	5
2.10.6 Vibration 12	5
2.11 Acoustics 13	5
2.12 Electromagnetic immunity 13	5
2.13 Reliability 14	5
2.13.1 Free Fall Protection feature 14	5
2.14 Agency certification 14	5
2.14.1 Safety certification 14	5
2.14.2 Electromagnetic compatibility 14	5
2.14.3 FCC verification 15	5
2.15 Environmental protection 16	5
2.15.1 European Union Restriction of Hazardous Substances (RoHS) 16	5
2.15.2 China Restriction of Hazardous Substances (RoHS) Directive 16	5
2.16 Corrosive environment 16	5
3.0 Configuring and mounting the drive 17	5
3.1 Handling and static-discharge precautions 17	5
3.2 Configuring the drive 18	5
3.3 Serial ATA cables and connectors 18	5
3.4 Drive mounting 19	5
4.0 Serial ATA (SATA) interface 21	5
4.1 Hot-Plug compatibility 21	5
4.2 Serial ATA device plug connector pin definitions 21	5
4.3 Supported ATA commands 23	5
4.3.1 Identify Device command 26	5
4.3.2 Set Features command 29	5
4.3.3 S.M.A.R.T. commands 31	5
5.0 Seagate Technology support services 33	5
Figure 1. Typical +5V only startup and operation current profile 9	7
Figure 2. Serial ATA connectors 18	7
Figure 3. Attaching SATA cabling 18	7
Figure 4. Mounting dimensions-top, side and end view 19	7
1.0 Introduction	9
1.1 About the Serial ATA interface	10
2.0 Drive specifications	11
2.1 Specification summary table	11
2.2 Formatted capacity	13
2.2.1 LBA mode	13
2.3 Default logical geometry	13
2.4 Physical organization	14
2.5 Recording and interface technology	14
2.6 Physical characteristics	14
2.7 Seek time	15
2.8 Start/stop times	15
2.9 Power specifications	16
2.9.1 Power consumption	16
2.9.1.1 Typical current profile	17
2.9.2 Deferred spinup	17
2.9.3 Conducted noise	17
2.9.4 Voltage tolerance	17
2.9.5 Power-management modes	18
2.10 Environmental specifications	18
2.10.1 Ambient temperature	18
2.10.2 Temperature gradient	19
2.10.3 Humidity	19
2.10.3.1 Relative humidity	19
2.10.3.2 Wet bulb temperature	19
2.10.4 Altitude	19
2.10.5 Shock	20
2.10.5.1 Operating shock	20
2.10.5.2 Nonoperating shock	20
2.10.6 Vibration	20
2.10.6.1 Operating vibration	20
2.10.6.2 Nonoperating vibration	20
2.11 Acoustics	21
2.12 Electromagnetic immunity	21
2.13 Reliability	22
2.13.1 Free Fall Protection feature	22
2.14 Agency certification	22
2.14.1 Safety certification	22
2.14.2 Electromagnetic compatibility	22
2.14.3 FCC verification	23
2.15 Environmental protection	24
2.15.1 European Union Restriction of Hazardous Substances (RoHS)	24
2.15.2 China Restriction of Hazardous Substances (RoHS) Directive	24
2.16 Corrosive environment	24
3.0 Configuring and mounting the drive	25
3.1 Handling and static-discharge precautions	25
3.2 Configuring the drive	26
3.3 Serial ATA cables and connectors	26
3.4 Drive mounting	27
4.0 Serial ATA (SATA) interface	29
4.1 Hot-Plug compatibility	29
4.2 Serial ATA device plug connector pin definitions	29
4.3 Supported ATA commands	31
4.3.1 Identify Device command	34
4.3.2 Set Features command	37
4.3.3 S.M.A.R.T. commands	39
5.0 Seagate Technology support services	41
A	43
B	43
C	43
D	43
E	43
F	43
G	43
H	44
I	44
K	44
L	44
M	44
N	44
O	44
P	44
Q	44
R	44
S	45
T	45
U	45
V	45

Match case Limit results 1 per page

Momentus 5400.5 SATA Product Manual, Rev. B

2.0

Drive specifications

Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal

power. For convenience, the phrases

the drive

and

this drive

are used throughout this manual to indicate the

ST9320320AS,

ST9250320AS,

ST9200321AS,

ST9160310AS,

ST9160310ASG,

ST9120310AS,

ST9120310ASG, ST980310AS and ST980310ASG models.

2.1

Specification summary table

The specifications listed in this table are for quick reference. For details on specification measurement or defi-

nition, see the appropriate section of this manual.

Table 1:

Drive specifications

Drive specification

ST9320320AS

ST9250320AS

ST9200321AS

ST9160310AS

ST9160310ASG

ST9120310AS

ST9120310ASG

ST980310AS

ST980310ASG

Formatted Gbytes

(512 bytes/sector)*

320

250

200

160

120

Guaranteed sectors

625,142,448

488,397,168

390,721,968

312,581,808

234,441,648

156,301,488

Bytes per sector

512

Physical read/write heads

4 or 3

Discs

Cache (Mbytes)

Recording density in BPI

(bits/inch avg)

1,337k

Track density TPI (tracks/inch avg)

190k

Areal density (Gbits/inch

avg)

254

Spindle speed (RPM)

5,400

Average latency (msec)

5.6

Internal transfer rate

(Mbits/sec max)

830

I/O data transfer rate

(Mbytes/sec max)

300

ATA data-transfer modes supported

SATA 1.0, Serial ATA Revision 2.6

PIO modes 0–4

Multiword DMA modes 0–2

Ultra DMA modes 0–6

Height (max)

9.5 +/- 0.2 mm (0.374 +/- .0078 inches)

Width (max)

69.85 mm (2.75 +/- 0.0098 inches)

Length (max)

100.5 +/- 0.25 mm (3.957 +/- 0.010 inches)

Weight (max)

98.8 grams (0.218 lb)

93.5 grams (0.206 lb)

Power-on to ready (sec typical)

3.4

Standby to ready (sec typical)

3.2