Home » Seagate Manuals » Hard Drives » Seagate STM980215A » Manual Viewer

Seagate STM980215A Maxtor MobileMax PATA Product Manual - Page 18

Table 3, pecifications summary

Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Table 3: STM940215A specifications summary Drive specification Formatted capacity (512 bytes/sector)* Guaranteed sectors Bytes per sector Physical read/write heads Discs Cache Recording density (typical) Track density (typical) Areal density (max) Spindle speed Internal data transfer rate (max) I/O data-transfer rate (max) ATA data-transfer modes supported Height Width Length Weight Average latency Power-on to ready Standby to ready Track-to-track seek time Average random seek , write Average random seek, read Average random seek Full-stroke seek Startup current 5V Seek power Read/write power Idle mode (low power) Standby mode Sleep mode Voltage tolerance (including noise) Ambient temperature Temperature gradient (noncondensing) Relative humidity (noncondensing) Relative humidity gradient Wet bulb temperature (max) Altitude, operating Altitude, nonoperating (below mean sea level) STM940215A 40 Gbytes 78,140,160 512 1 1 2 Mbytes 835k bits/inch (BPI) 150k tracks/inch (TPI) 132 Gbits/inch2 5,400 RPM 336 Mbits/sec (42 Mbytes/sec) 100 Mbytes/sec PIO modes 0-4 Multiword DMA modes 0-2 Ultra DMA modes 0-5 9.5 +/-0.2 mm (0.374 +/-.008 inches) 69.85 +/-0.25 mm (2.750 +/-0.010 inches) 100.50 +/-0.25 mm (3.957 +/-0.010 inches) 100 grams (0.220 lb) typical 5.6 msec 3.5 sec typical 3.0 sec typical 1.0 msec typical (read) 1.5 msec typical (write) 14.5 msec typical 12.5 msec typical 12.5 msec typical 22 msec (typical) 24 msec (max) 1.0 amps typical 2.0 watts typical Read: 2.0 watts typical Write: 1.8 watts typical 0.8 watts typical 0.26 watts typical*** 0.26 watts typical*** 5V ± 5% 5° to 55°C (operating) -40° to 70°C (nonoperating) 20°C per hour max (operating) 30°C per hour max (nonoperating) 5% to 90% (operating) 5% to 95% (nonoperating) 30% per hour max 30°C (operating) 38°C (nonoperating) -304.8 m to 3,048 m (-1000 ft to 10,000 ft) -304.8 m to 12,192 m (-1,000 ft to 40,000 ft) max 8 MobileMax Product Manual, Rev. A

Section	Page
1.0 Introduction 1	7
2.0 Drive specifications 3	7
2.1 Specification summary 3	7
2.2 Formatted capacity 10	7
2.3 Default logical geometry 10	7
2.4 Physical organization 10	7
2.5 Recording and interface technology 11	7
2.6 Physical characteristics 11	7
2.7 Seek time 11	7
2.8 Time to ready 12	7
2.9 Power specifications 12	7
2.9.1 Power consumption 12	7
2.9.2 Conducted noise 13	7
2.9.3 Voltage tolerance 13	7
2.10 Power-management modes 14	7
2.11 Environmental specifications 15	7
2.11.1 Ambient temperature 15	7
2.11.2 Temperature gradient 15	7
2.11.3 Humidity 15	7
2.11.4 Altitude 15	7
2.11.5 Shock 16	7
2.11.6 Vibration 16	7
2.12 Acoustics 17	7
2.13 Electromagnetic immunity 17	7
2.14 Reliability 18	7
2.15 Agency certification 18	7
2.15.1 Safety certification 18	7
2.15.2 Electromagnetic compatibility 18	7
2.15.3 FCC verification 19	7
2.16 Environmental protection 20	7
2.16.1 European Union Restriction of Hazardous Substances (RoHS) 20	7
2.17 Corrosive environment 20	7
3.0 Configuring and mounting the drive 21	7
3.1 Handling and static discharge precautions 21	7
3.2 Jumper settings 22	7
3.2.1 Master/slave configuration 22	7
3.2.2 Cable-select option 22	7
3.3 Mounting the drive 23	7
4.0 ATA interface 25	7
4.1 ATA interface signals and connector pins 25	7
4.1.1 Supported ATA commands 26	7
4.1.2 Identify Device command 28	7
4.1.3 Set Features command 31	7
5.0 Compatibility summary 33	7
5.1 Installation considerations 33	7
5.2 BIOS versions tested 35	7
5.3 Operating system versions tested 36	7
5.4 Compatibility test configurations 36	7
5.5 Other certification 36	7
6.0 Maxtor support services 37	7
Figure 1. Typical 5V startup and operation current profile 13	9
Figure 2. Jumper settings 22	9
Figure 3. Mounting dimensions-top, side and end view 23	9
1.0 Introduction	11
2.0 Drive specifications	13
2.1 Specification summary	13
2.2 Formatted capacity	20
2.3 Default logical geometry	20
2.4 Physical organization	20
2.5 Recording and interface technology	21
2.6 Physical characteristics	21
2.7 Seek time	21
2.8 Time to ready	22
2.9 Power specifications	22
2.9.1 Power consumption	22
2.9.1.1 Typical current profile	23
2.9.2 Conducted noise	23
2.9.3 Voltage tolerance	23
2.10 Power-management modes	24
2.11 Environmental specifications	25
2.11.1 Ambient temperature	25
2.11.2 Temperature gradient	25
2.11.3 Humidity	25
2.11.3.1 Relative humidity	25
2.11.3.2 Wet bulb temperature	25
2.11.4 Altitude	25
2.11.5 Shock	26
2.11.5.1 Operating shock	26
2.11.5.2 Nonoperating shock	26
2.11.6 Vibration	26
2.11.6.1 Operating vibration	26
2.11.6.2 Nonoperating vibration	26
2.12 Acoustics	27
2.13 Electromagnetic immunity	27
2.14 Reliability	28
2.15 Agency certification	28
2.15.1 Safety certification	28
2.15.2 Electromagnetic compatibility	28
2.15.3 FCC verification	29
2.16 Environmental protection	30
2.16.1 European Union Restriction of Hazardous Substances (RoHS)	30
2.17 Corrosive environment	30
3.0 Configuring and mounting the drive	31
3.1 Handling and static discharge precautions	31
3.2 Jumper settings	32
3.2.1 Master/slave configuration	32
3.2.2 Cable-select option	32
3.3 Mounting the drive	33
4.0 ATA interface	35
4.1 ATA interface signals and connector pins	35
4.1.1 Supported ATA commands	36
4.1.2 Identify Device command	38
4.1.3 Set Features command	41
5.0 Compatibility summary	43
5.1 Installation considerations	43
5.2 BIOS versions tested	45
5.3 Operating system versions tested	46
5.4 Compatibility test configurations	46
5.5 Other certification	46

Match case Limit results 1 per page

MobileMax Product Manual, Rev. A

Table 3:

STM940215A s

pecifications summary

Drive specification

STM940215A

Formatted capacity (512 bytes/sector)*

40 Gbytes

Guaranteed sectors

78,140,160

Bytes per sector

512

Physical read/write heads

Discs

Cache

2 Mbytes

Recording density (typical)

835k bits/inch (BPI)

Track density (typical)

150k tracks/inch (TPI)

Areal density (max)

132 Gbits/inch

Spindle speed

5,400 RPM

Internal data transfer rate (max)

336 Mbits/sec (42 Mbytes/sec)

I/O data-transfer rate (max)

100 Mbytes/sec

ATA data-transfer modes supported

PIO modes 0–4

Multiword DMA modes 0–2

Ultra DMA modes 0–5

Height

9.5 +/-0.2 mm (0.374 +/-.008 inches)

Width

69.85 +/-0.25 mm (2.750 +/-0.010 inches)

Length

100.50 +/-0.25 mm (3.957 +/-0.010 inches)

Weight

100 grams (0.220 lb) typical

Average latency

5.6 msec

Power-on to ready

3.5 sec typical

Standby to ready

3.0 sec typical

Track-to-track seek time

1.0 msec typical (read)

1.5 msec typical (write)

Average random seek , write

14.5 msec typical

Average random seek, read

12.5 msec typical

Average random seek

12.5 msec typical

Full-stroke seek

22 msec (typical)

24 msec (max)

Startup current 5V

1.0 amps typical

Seek power

2.0 watts typical

Read/write power

Read: 2.0 watts typical

Write: 1.8 watts typical

Idle mode (low power)

0.8 watts typical

Standby mode

0.26 watts typical***

Sleep mode

0.26 watts typical***

Voltage tolerance (including noise)

5V ± 5%

Ambient temperature

5° to 55°C (operating)

–40° to 70°C (nonoperating)

Temperature gradient

(noncondensing)

20°C per hour max (operating)

30°C per hour max (nonoperating)

Relative humidity

(noncondensing)

5% to 90% (operating)

5% to 95% (nonoperating)

Relative humidity gradient

30% per hour max

Wet bulb temperature (max)

30°C (operating)

38°C (nonoperating)

Altitude, operating

–304.8 m to 3,048 m (–1000 ft to 10,000 ft)

Altitude, nonoperating (below mean sea level)

–304.8 m to 12,192 m (–1,000 ft to 40,000 ft) max