Home » Seagate Manuals » Hard Drives » Seagate STM980215A » Manual Viewer

Seagate STM980215A Maxtor MobileMax PATA Product Manual - Page 23

Typical current profile, Conducted noise, Note., Voltage tolerance

Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

2.9.1.1 Typical current profile Figure 4. Typical 5V startup and operation current profile 2.9.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line. Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave injected noise at up to 10 MHz. Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current. 2.9.3 Voltage tolerance Voltage tolerance (including noise): 5V ± 5% MobileMax Product Manual, Rev. A 13

Section	Page
1.0 Introduction 1	7
2.0 Drive specifications 3	7
2.1 Specification summary 3	7
2.2 Formatted capacity 10	7
2.3 Default logical geometry 10	7
2.4 Physical organization 10	7
2.5 Recording and interface technology 11	7
2.6 Physical characteristics 11	7
2.7 Seek time 11	7
2.8 Time to ready 12	7
2.9 Power specifications 12	7
2.9.1 Power consumption 12	7
2.9.2 Conducted noise 13	7
2.9.3 Voltage tolerance 13	7
2.10 Power-management modes 14	7
2.11 Environmental specifications 15	7
2.11.1 Ambient temperature 15	7
2.11.2 Temperature gradient 15	7
2.11.3 Humidity 15	7
2.11.4 Altitude 15	7
2.11.5 Shock 16	7
2.11.6 Vibration 16	7
2.12 Acoustics 17	7
2.13 Electromagnetic immunity 17	7
2.14 Reliability 18	7
2.15 Agency certification 18	7
2.15.1 Safety certification 18	7
2.15.2 Electromagnetic compatibility 18	7
2.15.3 FCC verification 19	7
2.16 Environmental protection 20	7
2.16.1 European Union Restriction of Hazardous Substances (RoHS) 20	7
2.17 Corrosive environment 20	7
3.0 Configuring and mounting the drive 21	7
3.1 Handling and static discharge precautions 21	7
3.2 Jumper settings 22	7
3.2.1 Master/slave configuration 22	7
3.2.2 Cable-select option 22	7
3.3 Mounting the drive 23	7
4.0 ATA interface 25	7
4.1 ATA interface signals and connector pins 25	7
4.1.1 Supported ATA commands 26	7
4.1.2 Identify Device command 28	7
4.1.3 Set Features command 31	7
5.0 Compatibility summary 33	7
5.1 Installation considerations 33	7
5.2 BIOS versions tested 35	7
5.3 Operating system versions tested 36	7
5.4 Compatibility test configurations 36	7
5.5 Other certification 36	7
6.0 Maxtor support services 37	7
Figure 1. Typical 5V startup and operation current profile 13	9
Figure 2. Jumper settings 22	9
Figure 3. Mounting dimensions-top, side and end view 23	9
1.0 Introduction	11
2.0 Drive specifications	13
2.1 Specification summary	13
2.2 Formatted capacity	20
2.3 Default logical geometry	20
2.4 Physical organization	20
2.5 Recording and interface technology	21
2.6 Physical characteristics	21
2.7 Seek time	21
2.8 Time to ready	22
2.9 Power specifications	22
2.9.1 Power consumption	22
2.9.1.1 Typical current profile	23
2.9.2 Conducted noise	23
2.9.3 Voltage tolerance	23
2.10 Power-management modes	24
2.11 Environmental specifications	25
2.11.1 Ambient temperature	25
2.11.2 Temperature gradient	25
2.11.3 Humidity	25
2.11.3.1 Relative humidity	25
2.11.3.2 Wet bulb temperature	25
2.11.4 Altitude	25
2.11.5 Shock	26
2.11.5.1 Operating shock	26
2.11.5.2 Nonoperating shock	26
2.11.6 Vibration	26
2.11.6.1 Operating vibration	26
2.11.6.2 Nonoperating vibration	26
2.12 Acoustics	27
2.13 Electromagnetic immunity	27
2.14 Reliability	28
2.15 Agency certification	28
2.15.1 Safety certification	28
2.15.2 Electromagnetic compatibility	28
2.15.3 FCC verification	29
2.16 Environmental protection	30
2.16.1 European Union Restriction of Hazardous Substances (RoHS)	30
2.17 Corrosive environment	30
3.0 Configuring and mounting the drive	31
3.1 Handling and static discharge precautions	31
3.2 Jumper settings	32
3.2.1 Master/slave configuration	32
3.2.2 Cable-select option	32
3.3 Mounting the drive	33
4.0 ATA interface	35
4.1 ATA interface signals and connector pins	35
4.1.1 Supported ATA commands	36
4.1.2 Identify Device command	38
4.1.3 Set Features command	41
5.0 Compatibility summary	43
5.1 Installation considerations	43
5.2 BIOS versions tested	45
5.3 Operating system versions tested	46
5.4 Compatibility test configurations	46
5.5 Other certification	46