Sealey CP1205 Instruction Manual - Page 2

fig.1

Get Sealey CP1205 PDF manuals and user guides View all Sealey CP1205 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

4. OPERATION fig.1 ‰ 4.1. 4.2. 4.3. 4.4. 4.5. 4.6. 4.7. 4.8. WARNING! Before use, ensure that you have read and understood Section 1 Safety Instructions. To attach/remove the applicator pad depress the chuck lock button behind the chuck (fig.1) and screw/unscrew the applicator pad. Release the chuck lock button and check that applicator pad is locked into chuck before switching on. Attach the battery to the sander. The battery charge level indicator LEDs (fig.1) show charge (three green lights indicate full charge). Set the required speed by use of the speed selector switch (fig.1). Unlock the drive mechanism by use of the slide switch (fig.1). Grip the side handle (not shown) and start the polisher by gentle and slow application of pressure on the trigger (fig.1). Increase/decrease the speed of the polisher using the variable speed control trigger (fig.1) to suit the task in hand. Ensure that the above features are working correctly prior to use. 5. MAINTENANCE ‰ 5.1. 5.1.1. 5.1.2. 5.2. ‰ 5.2.1. 5.2.2. 5.2.3. 5.2.4. 5.2.5. WARNING: Always disconnect the battery before carrying out any inspection, maintenance or cleaning. General inspection Regularly check that all the fixing screws are tight. Repairs should only be carried out by an authorised service centre. Cleaning WARNING: Always wear protective equipment including eye protection and gloves when cleaning this tool. Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and shorten the device's service life. Clean the body of your machine with a soft brush, or dry cloth. Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient, a mild detergent on a mildly damp cloth is recommended. Water must never come into contact with the tool. Ensure the tool is thoroughly dry before using it. If available, use clean, dry, compressed air to blow through the ventilation holes (where applicable). WARNING! - Risk of Hand Arm Vibration Injury. This tool may cause Hand Arm Vibration Syndrome if its use is not managed adequately. This tool is subject to the vibration testing section of the Machinery Directive 2006/42/EC. This tool is to be operated in accordance with these instructions. Measured vibration emission value (a): 4.213m/s² Uncertainty value (k): 1.5m/s² Please note that the application of the tool to a sole specialist task may produce a different average vibration emission. We recommend that a specific evaluation of the vibration emission is conducted prior to commencing with a specialist task. A health and safety assessment by the user (or employer) will need to be carried out to determine the suitable duration of use for each tool. NB: Stated Vibration Emission values are type-test values and are intended to be typical. Whilst in use, the actual value will vary considerably from and depend on many factors. Such factors include; the operator, the task and the inserted tool or consumable. NB: ensure that the length of leader hoses is sufficient to allow unrestricted use, as this also helps to reduce vibration. The state of maintenance of the tool itself is also an important factor, a poorly maintained tool will also increase the risk of Hand Arm Vibration Syndrome. Health surveillance. We recommend a programme of health surveillance to detect early symptoms of vibration injury so that management procedures can be modified accordingly. Personal protective equipment. We are not aware of any personal protective equipment (PPE) that provides protection against vibration injury that may result from the uncontrolled use of this tool. We recommend a sufficient supply of clothing (including gloves) to enable the operator to remain warm and dry and maintain good blood circulation in fingers etc. Please note that the most effective protection is prevention, please refer to the Correct Use and Maintenance section in these instructions. Guidance relating to the management of hand arm vibration can be found on the HSC website www.hse.gov.uk - Hand-Arm Vibration at Work. © Jack Sealey Limited Original Language Version CP1205 Issue 2 11/05/20

  • 1
  • 2
  • 3
4. OPERATION
±
WARNING!
Before use, ensure that you have read and understood Section 1 Safety Instructions.
4.1.
To attach/remove the applicator pad depress the chuck lock button behind the chuck (fig.1) and screw/unscrew the applicator pad.
4.2.
Release the chuck lock button and check that applicator pad is locked into chuck before switching on.
4.3.
Attach the battery to the sander. The battery charge level indicator LEDs (fig.1) show charge (three green lights indicate full charge).
4.4.
Set the required speed by use of the speed selector switch (fig.1).
4.5.
Unlock the drive mechanism by use of the slide switch (fig.1).
4.6.
Grip the side handle (not shown) and start the polisher by gentle and slow application of pressure on the trigger (fig.1).
4.7.
Increase/decrease the speed of the polisher using the variable speed control trigger (fig.1) to suit the task in hand.
4.8.
Ensure that the above features are working correctly prior to use.
5. MAINTENANCE
±
WARNING:
Always disconnect the battery before carrying out any inspection, maintenance or cleaning.
5.1.
General inspection
5.1.1.
Regularly check that all the fixing screws are tight.
5.1.2.
Repairs should only be carried out by an authorised service centre.
5.2.
Cleaning
±
WARNING:
Always wear protective equipment including eye protection and gloves when cleaning this tool.
5.2.1.
Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and shorten the device’s service life.
5.2.2.
Clean the body of your machine with a soft brush, or dry cloth.
5.2.3.
Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient, a mild detergent on a mildly damp cloth is
recommended.
5.2.4.
Water must never come into contact with the tool. Ensure the tool is thoroughly dry before using it.
5.2.5.
If available, use clean, dry, compressed air to blow through the ventilation holes (where applicable).
WARNING! – Risk of Hand Arm Vibration Injury.
This tool may cause Hand Arm Vibration Syndrome if its use is not managed adequately.
T
his tool is subject to the vibration testing section of the Machinery Directive 2006/42/EC.
This tool is to be operated in accordance with these instructions.
Measured vibration emission value (a):
4.213m/s²
Uncertainty value (k):
1.5m/s²
Please note that the application of the tool to a sole specialist task may produce a different average vibration emission. We recommend that a
specific evaluation of the vibration emission is conducted prior to commencing with a specialist task.
A health and safety assessment by the user (or employer) will need to be carried out to determine the suitable duration of use for each tool.
NB:
Stated Vibration Emission values are type-test values and are intended to be typical.
Whilst in use, the actual value will vary considerably from and depend on many factors.
Such factors include; the operator, the task and the inserted tool or consumable.
NB:
ensure that the length of leader hoses is sufficient to allow unrestricted use, as this also helps to reduce vibration.
The state of maintenance of the tool itself is also an important factor, a poorly maintained tool will also increase the risk of Hand Arm Vibration
Syndrome.
Health surveillance.
W
e recommend a programme of health surveillance to detect early symptoms of vibration injury so that management procedures can be modified
accordingly.
Personal protective equipment.
W
e are not aware of any personal protective equipment (PPE) that provides protection against vibration injury that may result from the
uncontrolled use of this tool. We recommend a sufficient supply of clothing (including gloves) to enable the operator to remain warm and dry and
maintain good blood circulation in fingers etc. Please note that the most effective protection is prevention, please refer to the Correct Use and
Maintenance section in these instructions. Guidance relating to the management of hand arm vibration can be found on the HSC website
w
ww.hse.gov.uk - Hand-Arm Vibration at Work
.
Original Language Version
© Jack Sealey Limited
fig.1
CP1205
Issue 2
11/05/20