Sealey SB995 Instruction Manual - Page 1

Sealey SB995 Manual

Get Sealey SB995 PDF manuals and user guides View all Sealey SB995 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 1 highlights

SHOT BLASTING KIT 22.6KG/40KG CAPACITY MODEL NO'S: SB994, SB995 Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE. Refer to instruction manual Wear a mask 1. SAFETY Wear protective gloves Wear ear protection Wear eye protection ‰ WARNING! Turn off, or disconnect from, air supply before servicing or performing any maintenance and when unit is not in use. Failure to comply with this instruction may damage the unit and will invalidate your warranty. ‰ WARNING! Wear approved ear, eye, hand and respiratory protection when operating the blaster. A full range of personal safety equipment is available from your Sealey stockists. 9 Maintain correct balance and ensure firm footing. 9 Spillages of abrasive material, which may be slippery, must be cleaned up immediately to avoid injury. 9 Locate blaster in a suitable, well ventilated, work area. Keep area clean and tidy and free from unrelated materials, and ensure that there is adequate lighting. 9 Maintain the blaster in good condition (use an authorised service agent). 9 Replace or repair damaged parts. Use recommended parts only. Non-authorised parts may be dangerous and will invalidate the warranty. 9 Keep the unit clean for best and safest performance. 9 Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain long hair. 9 Always keep the blast nozzle directed at the work piece. 9 If a failure or malfunction occurs immediately disconnect from air supply. 9 Keep all other persons away from the working area. Contact with high pressure blast or inhaling the dust generated is dangerous. 8 DO NOT use the blaster for any purpose other than that for which it is designed. 8 DO NOT operate the blaster if any parts are missing or damaged as this may cause failure and/or personal injury. 8 DO NOT use any abrasive which contains free silica. We recommend Sealey Shot Blasting Grit. 8 DO NOT attempt to clear a blocked nozzle while the unit is pressurised. 8 DO NOT allow untrained persons to operate the blaster. 8 DO NOT get the blaster wet or use in damp or wet locations or areas where there is condensation. 8 DO NOT leave the blaster operating unattended. 8 DO NOT operate the blaster when you are tired, under the influence of alcohol, drugs or intoxicating medication. 8 DO NOT stand or sit on the blaster. 8 DO NOT direct air from the air hose at yourself or others. 8 DO NOT operate system with air supply exceeding 125psi (8.6bar). 2. INTRODUCTION Compact and portable shot blasting kit. Large capacity hopper with handle and heavy-duty rubber wheels for easy manoeuvrability. Supplied with 3m grit hose, fitted with a heavy-duty shot blasting gun and four ceramic nozzles. 3. SPECIFICATION Air Consumption: Inlet size: Maximum Fill Weight: Nozzle Size(s): Operating Pressure: Overall Dimensions (W x D x H): SB994 SB995 10-16cfm 1/4" BSP 22.6kg 40kg 4, 5, 6, 7mm 60-125psi 330 x 370 x 685mm 432 x 458 x 940mm 4. AIR SUPPLY ‰ WARNING! Ensure the air supply does not exceed 125psi (8.6 bar) while operating the unit. Too high an air pressure will shorten the life of the unit due to excessive wear and may cause damage and/or personal injury. 9 Ensure the blaster air valve (trigger) is in the 'Off' position before connecting to the air supply. 9 Keep the air hose between the compressor and the unit a reasonable length and install an air filter and water separator (fig.1). 9 Drain the air tank daily. Water in the air line will damage the unit. 9 The recommended hook-up procedure is shown in fig.1. 9 The minimum hose diameter should be 1/4" I.D. and fittings must have the same inside dimensions. © Jack Sealey Limited Original Language Version SB994,SB995 Issue:5 (3) 12/11/21

  • 1
  • 2
SHOT BLASTING KIT 22.6KG/40KG CAPACITY
MODEL NO’S:
SB994, SB995
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
1. SAFETY
±
WARNING!
Turn off, or disconnect from, air supply before servicing or performing any maintenance and when unit is not in use.
Failure to comply with this instruction may damage the unit and will invalidate your warranty.
±
WARNING!
Wear approved ear, eye, hand and respiratory protection when operating the blaster. A full range of personal safety
equipment is available from your Sealey stockists.
9
Maintain correct balance and ensure firm footing.
9
Spillages of abrasive material, which may be slippery, must be cleaned up immediately to avoid injury.
9
Locate blaster in a suitable, well ventilated, work area. Keep area clean and tidy and free from unrelated materials, and ensure that there
is adequate lighting.
9
Maintain the blaster in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use recommended parts only. Non-authorised parts may be dangerous and will invalidate the warranty.
9
Keep the unit clean for best and safest performance.
9
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain long hair.
9
Always keep the blast nozzle directed at the work piece.
9
If a failure or malfunction occurs
immediately disconnect from air supply.
9
Keep all other persons away from the working area. Contact with high pressure blast or inhaling the dust generated is dangerous.
8
DO NOT
use the blaster for any purpose other than that for which it is designed.
8
DO NOT
operate the blaster if any parts are missing or damaged as this may cause failure and/or personal injury.
8
DO NOT
use any abrasive which contains free silica.
We recommend Sealey Shot Blasting Grit.
8
DO NOT
attempt to clear a blocked nozzle while the unit is pressurised.
8
DO NOT
allow untrained persons to operate the blaster.
8
DO NOT
get the blaster wet or use in damp or wet locations or areas where there is condensation.
8
DO NOT
leave the blaster operating unattended.
8
DO NOT
operate the blaster when you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT
stand or sit on the blaster.
8
DO NOT
direct air from the air hose at yourself or others.
8
DO NOT
operate system with air supply exceeding 125psi (8.6bar).
2. INTRODUCTION
Compact and portable shot blasting kit. Large capacity hopper with handle and heavy-duty rubber wheels for easy manoeuvrability. Supplied with
3m grit hose, fitted with a heavy-duty shot blasting gun and four ceramic nozzles.
3. SPECIFICATION
4. AIR SUPPLY
±
WARNING!
Ensure the air supply does not exceed 125psi (8.6 bar) while operating the unit. Too high an air pressure will shorten the
life of the unit due to excessive wear and may cause damage and/or personal injury.
9
Ensure the blaster air valve (trigger) is in the ‘Off’ position before connecting to the air supply.
9
Keep the air hose between the compressor and the unit a reasonable length and install an air filter and water separator (fig.1).
9
Drain the air tank daily. Water in the air line will damage the unit.
9
The recommended hook-up procedure is shown in fig.1.
9
The minimum hose diameter should be 1/4” I.D. and fittings must have the same inside dimensions.
SB994,SB995
Issue:5 (3) 12/11/21
Original Language Version
© Jack Sealey Limited
Refer to
instruction
manual
Wear a mask
Wear
protective
gloves
Wear ear
protection
Wear eye
protection
SB994
SB995
Air Consumption:
10-16cfm
Inlet size:
1/4” BSP
Maximum Fill Weight:
22.6kg
40kg
Nozzle Size(s):
4, 5, 6, 7mm
Operating Pressure:
60-125psi
Overall Dimensions (W x D x H):
330 x 370 x 685mm
432 x 458 x 940mm