Sealey SB995 Instruction Manual - Page 2

fig.1, fig.2

Get Sealey SB995 PDF manuals and user guides View all Sealey SB995 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

fig.1 fig.2 9 Use correct hoses and fittings. DO NOT use quick change couplings as they add weight and can cause failure due to vibration. Add a leader hose and connect coupling between this and supply hose. 9 Keep hoses away from heat, oil and sharp edges. Check hoses for wear and ensure that all connections are secure. 5. ASSEMBLY ‰ 5.1. 5.1.1. 5.1.2. 5.1.3. 5.1.4. 5.1.5. 5.1.6. 5.1.7. 5.2. 5.2.1. 5.2.2. 5.2.3. 5.2.4. 5.2.5. 5.2.6. 5.2.7. 5.2.8. WARNING! Before operating the unit ensure you read, understand and apply Section 1 Safety Instructions. NOTE: Numbers in brackets refer to the item numbers in the Parts List. MODEL SB994 (Refer to SB994 parts diagram) Attach lower handle axle assembly (4) to the barrel assembly (1) using screws (8), washers (6) and nuts (5), do not fully tighten. Slide the upper handle (2) onto the lower handle and align the hole, using screw (7), washers (6) push the screw through into the barrel assembly and secure using washer (6) and nut (5). Tighten all screws securely. Push a split pin (11) through the inner hole of the axle and secure using pliers to bend round the pin, slide a washer ('*O-ring') (9) on the axle so that it butts up against the split pin, slide a wheel (10) onto the axle, followed by another washer (*) (9) and secure with a split pin through the outer hole in the axle shaft. Repeat for the other side. Slide the front leg (3) into the tube on the barrel assembly, align the holes and secure using screw (7), washers (6) and nut (5). Slide a hose clamp (13) over the end of the hose and push onto the outlet tube of the barrel assembly. NOTE: DO NOT push the hose on so far that it covers the vent hole in the outlet tube. Connect the other end of the hose to the sanding gun (12) using hose clamp (13). Fit an appropriate air line connection compatible with your air supply, see section 4 and the Specification in section 2. MODEL SB995 (Refer to SB995 parts diagram) Loosely attach handle (3) to barrel assembly (1) using screws (7), washers (5) and nuts (6). Loosely attach base support (2) to the barrel assembly using screws (4) washers (5) and nuts (6), ensure that the gun holder is facing upwards as shown in the parts diagram. Attach the base bar (8) to the base support bar, align the holes at the rear of the base with the holes in the handle (3) and slide the axle (9) through both the handle and the base section to locate. Ensure that the axle sticks out evenly on both sides of the handle. Slide washer (10) and wheel (11) onto one side of the axle, slide the other washer onto the axle and secure using split pin (12). Repeat for the other wheel assembly. Tighten all screws, ensuring that the handle and base are square with the barrel assembly. Attach the end of the hose with the right angle bend (15) to the outlet tube of the barrel assembly using hose clamp (14), ensuring that the vent hole in the tube is facing upwards. Attach the other end of the hose onto the guns using hose clamp (14). Fit an appropriate air line connection compatible with your air supply, see section 4 and the Specification in section 2. 6. OPERATION ‰ ‰ ‰ 6.1. 6.2. 6.3. 6.4. 6.5. 6.6. ‰ WARNING! Ensure that you read, understand and apply the safety instructions in Section 1 before use. WARNING! Wear approved ear, eye, hand and respiratory protection when operating the blaster. WARNING! Ensure the air supply does not exceed 120psi (8.2bar) while operating the unit. Fill the hopper with the required abrasive, checking to ensure it is clean and dry. Attach an airline to the gun and press the trigger. Before blasting unfamiliar material, spot test to ensure that damage/pitting will not occur to the material. Use even passes of the blaster to remove material such as rust, body filler or other soft materials. DO NOT blast in any one area for more than a few seconds at a time. The unit is supplied with 4 ceramic nozzles ranging from 4 to 7mm, select the appropriate nozzle for the task (fig.2). To change the nozzle, disconnect from the air supply and unscrew the head screw, insert the nozzle as shown in fig.2 and refit the head screw. WARNING! DO NOT use the sand blaster without a nozzle fitted. ENVIRONMENT PROTECTION Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations. Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 [email protected] www.sealey.co.uk © Jack Sealey Limited Original Language Version SB994,SB995 Issue:5 (3) 12/11/21

  • 1
  • 2
9
Use correct hoses and fittings.
DO NOT
use quick change couplings as they add weight and can cause failure due to vibration. Add a
leader hose and connect coupling between this and supply hose.
9
Keep hoses away from heat, oil and sharp edges. Check hoses for wear and ensure that all connections are secure.
5. ASSEMBLY
±
WARNING! Before operating the unit ensure you read, understand and apply Section 1 Safety Instructions.
NOTE: Numbers in brackets refer to the item numbers in the Parts List.
5.1.
MODEL SB994 (Refer to SB994 parts diagram)
5.1.1.
Attach lower handle axle assembly (4) to the barrel assembly (1) using screws (8), washers (6) and nuts (5), do not fully tighten.
5.1.2.
Slide the upper handle (2) onto the lower handle and align the hole, using screw (7), washers (6) push the screw through into the
barrel assembly and secure using washer (6) and nut (5). Tighten all screws securely.
5.1.3.
Push a split pin (11) through the inner hole of the axle and secure using pliers to bend round the pin, slide a washer (‘*O-ring’) (9) on the
axle so that it butts up against the split pin, slide a wheel (10) onto the axle, followed by another washer (*) (9) and secure with a split pin
through the outer hole in the axle shaft. Repeat for the other side.
5.1.4.
Slide the front leg (3) into the tube on the barrel assembly, align the holes and secure using screw (7), washers (6) and nut (5).
5.1.5.
Slide a hose clamp (13) over the end of the hose and push onto the outlet tube of the barrel assembly.
NOTE: DO NOT
push the hose on so far that it covers the vent hole in the outlet tube.
5.1.6.
Connect the other end of the hose to the sanding gun (12) using hose clamp (13).
5.1.7.
Fit an appropriate air line connection compatible with your air supply, see section 4 and the Specification in section 2.
5.2.
MODEL SB995 (Refer to SB995 parts diagram)
5.2.1.
Loosely attach handle (3) to barrel assembly (1) using screws (7), washers (5) and nuts (6).
5.2.2.
Loosely attach base support (2) to the barrel assembly using screws (4) washers (5) and nuts (6), ensure that the gun holder is facing
upwards as shown in the parts diagram.
5.2.3.
Attach the base bar (8) to the base support bar, align the holes at the rear of the base with the holes in the handle (3) and slide the
axle (9) through both the handle and the base section to locate. Ensure that the axle sticks out evenly on both sides of the handle.
5.2.4.
Slide washer (10) and wheel (11) onto one side of the axle, slide the other washer onto the axle and secure using split pin (12).
Repeat for the other wheel assembly.
5.2.5.
Tighten all screws, ensuring that the handle and base are square with the barrel assembly.
5.2.6.
Attach the end of the hose with the right angle bend (15) to the outlet tube of the barrel assembly using hose clamp (14), ensuring that
the vent hole in the tube is facing upwards.
5.2.7.
Attach the other end of the hose onto the guns using hose clamp (14).
5.2.8.
Fit an appropriate air line connection compatible with your air supply, see section 4 and the Specification in section 2.
6. OPERATION
±
WARNING!
Ensure that you read, understand and apply the safety instructions in Section 1 before use.
±
WARNING!
Wear approved ear, eye, hand and respiratory protection when operating the blaster.
±
WARNING!
Ensure the air supply does not exceed 120psi (8.2bar) while operating the unit.
6.1.
Fill the hopper with the required abrasive, checking to ensure it is clean and dry.
6.2.
Attach an airline to the gun and press the trigger.
6.3.
Before blasting unfamiliar material, spot test to ensure that damage/pitting will not occur to the material.
6.4.
Use even passes of the blaster to remove material such as rust, body filler or other soft materials.
DO NOT
blast in any one area
for more than a few seconds at a time.
6.5.
The unit is supplied with 4 ceramic nozzles ranging from 4 to 7mm, select the appropriate nozzle for the task (fig.2).
6.6.
To change the nozzle, disconnect from the air supply and unscrew the head screw, insert the nozzle as shown in fig.2 and refit the head
screw.
±
WARNING! DO NOT
use the sand blaster without a nozzle fitted.
fig.1
fig.2
Original Language Version
© Jack Sealey Limited
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
01284 703534
www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note
: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important
: No Liability is accepted for incorrect use of this product.
Warranty
: Guarantee is 12 months from purchase date, proof of which is required for any claim.
SB994,SB995
Issue:5 (3) 12/11/21