Sealey SC10 Instruction Manual - Page 1

Sealey SC10 Manual

Get Sealey SC10 PDF manuals and user guides View all Sealey SC10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 1 highlights

1TONNE FOLDING ENGINE CRANE MODEL NO: SC10.V4 Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE. Refer to instructions Wear protective Wear protective footwear gloves 1. SAFETY 9 Keep crane, lifting slings, support and beams in good working order and condition. Follow the inspection requirements as described in Section 4 Maintenance. Take immediate action to repair or replace damaged parts by contacting your supplier. Ensure that all accessory lifting devices are suitably certified. If crane is damaged, remove from service immediately. 9 Ensure the surface on which the crane is used is level, firm and capable of supporting the weight of the crane with maximum load - we recommend concrete. Never use the crane on tarmacadam or other soft surfaces. 9 Ensure the crane legs and jib extension are locked before use. 9 Keep children and unauthorised persons away from the working area. 9 Keep working area clean and tidy, free from unrelated materials and ensure that there is adequate lighting. 9 Ensure that load does not exceed the maximum lifting capacity of the crane. Overloading the crane is dangerous. Where appropriate use only the lifting points recommended by the manufacturer of the item to be lifted, e.g. vehicle engine. 9 Before lifting the load ensure that the crane jib is in the lowest practical position, that there are no obstacles which may snag the load whilst it is being lifted and that the area above the jib is clear. 9 To avoid injury, be fully aware of your own and other persons locations in relation to the lifting and lowering of the load. 9 Keep a sound footing and balance and ensure the floor is not slippery. 9 Ensure jib extension locking bolt and nut are in position before lifting. 9 Ensure the centre of gravity always remains inside the crane base. 8 DO NOT harness the load at an angle or use any attachments not verified as fit for purpose. 8 DO NOT allow the load to swing during lifting. 8 DO NOT allow the load to drop suddenly. Lower load with care, ensuring that you are fully aware of the condition of the surface onto which the load is to be placed. 8 DO NOT load crane beyond its rated capacity for each specified jib extension position as indicated in Section 2. The capacity of the crane reduces as the jib is extended. 8 DO NOT position any part of your body beneath the load. 8 DO NOT use the crane to move, or transport, a load other than for repositioning (see 3.2.6). The crane is a lifting device only. 8 DO NOT apply any sideways pressure to any part of the crane during lifting or when a load is suspended. 8 DO NOT attempt to adjust the safety valve, which has been set and sealed by the manufacturer. 8 DO NOT use this product to perform a task for which it is not designed. 8 DO NOT use the crane whilst tired or under the influence of drugs, alcohol or intoxicating medication. 8 DO NOT climb on the crane. 9 When not in use, fold the crane down and store in a safe, dry, childproof area. 9 This crane is designed for lifting within a garage or workshop environment. ‰ WARNING! Failure to heed safety and warning instructions may result in damage and/or personal injury and will invalidate the warranty. NOTE: ENSURE YOU HAVE READ AND UNDERSTOOD THE SAFETY INSTRUCTIONS AT THE BEGINNING OF THIS SECTION BEFORE YOU OPERATE THE CRANE. 2. INTRODUCTION Super economy model delivered in knock-down form for reduced freight cost. Fast folding model provides easy storage and transportation with heavy-duty castors. Weighs only 75kg and is perfect for mobile or workshop use. Side pump access with removable handle. 2.1. Supplier: IDENTIFICATION Sealey Power Products, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk, IP32 7AR. Model No: SC10.V4 © Jack Sealey Limited Original Language Version SC10.V4 Issue 4 (3) 26/05/21

  • 1
  • 2
  • 3
1TONNE FOLDING ENGINE CRANE
MODEL NO:
SC10.V4
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
1. SAFETY
9
Keep crane, lifting slings, support and beams in good working order and condition. Follow the inspection requirements as described
in Section 4 Maintenance.
Take immediate action to repair or replace damaged parts by contacting your supplier. Ensure that all
accessory lifting devices are suitably certified. If crane is damaged, remove from service immediately.
9
Ensure the surface on which the crane is used is level, firm and capable of supporting the weight of the crane with maximum load - we
recommend concrete. Never use the crane on tarmacadam or other soft surfaces.
9
Ensure the crane legs and jib extension are locked before use.
9
Keep children and unauthorised persons away from the working area.
9
Keep working area clean and tidy, free from unrelated materials and ensure that there is adequate lighting.
9
Ensure that load does not exceed the maximum lifting capacity of the crane. Overloading the crane is dangerous. Where appropriate use
only the lifting points recommended by the manufacturer of the item to be lifted, e.g. vehicle engine.
9
Before lifting the load ensure that the crane jib is in the lowest practical position, that there are no obstacles which may snag the load
whilst it is being lifted and that the area above the jib is clear.
9
To avoid injury, be fully aware of your own and other persons locations in relation to the lifting and lowering of the load.
9
Keep a sound footing and balance and ensure the floor is not slippery.
9
Ensure jib extension locking bolt and nut are in position before lifting.
9
Ensure the centre of gravity always remains inside the crane base.
8
DO NOT
harness the load at an angle or use any attachments not verified as fit for purpose.
8
DO NOT
allow the load to swing during lifting.
8
DO NOT
allow the load to drop suddenly. Lower load with care, ensuring that you are fully aware of the condition of the surface onto which
the load is to be placed.
8
DO NOT
load crane beyond its rated capacity for each specified jib extension position as indicated in Section 2. The capacity of the crane
reduces as the jib is extended.
8
DO NOT
position any part of your body beneath the load.
8
DO NOT
use the crane to move, or transport, a load other than for repositioning (see 3.2.6). The crane is a lifting device only.
8
DO NOT
apply any sideways pressure to any part of the crane during lifting or when a load is suspended.
8
DO NOT
attempt to adjust the safety valve, which has been set and sealed by the manufacturer.
8
DO NOT
use this product to perform a task for which it is not designed.
8
DO NOT
use the crane whilst tired or under the influence of drugs, alcohol or intoxicating medication.
8
DO NOT
climb on the crane.
9
When not in use, fold the crane down and store in a safe, dry, childproof area.
9
This crane is designed for lifting within a garage or workshop environment.
±
WARNING! Failure to heed safety and warning instructions may result in damage and/or personal injury and will invalidate the
warranty.
NOTE:
ENSURE YOU HAVE READ AND UNDERSTOOD THE SAFETY INSTRUCTIONS AT THE BEGINNING OF THIS SECTION BEFORE YOU OPERATE
THE CRANE.
2. INTRODUCTION
Super economy model delivered in knock-down form for reduced freight cost. Fast folding model provides easy storage and transportation with
heavy-duty castors. Weighs only 75kg and is perfect for mobile or workshop use. Side pump access with removable handle.
2.1.
IDENTIFICATION
Supplier:
Sealey Power Products,
Kempson Way,
Suffolk Business Park,
Bury St Edmunds,
Suffolk, IP32 7AR.
Model No:
SC10.V4
SC10.V4 Issue 4 (3) 26/05/21
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear protective
footwear
Wear protective
gloves