Sealey SUPERBOOST180 Instruction Manual - Page 1

Sealey SUPERBOOST180 Manual

Get Sealey SUPERBOOST180 PDF manuals and user guides View all Sealey SUPERBOOST180 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 1 highlights

instructions for superboost starter / charger model noS: SUPERBOOST 180.V5 &SUPERBOOST 200.V4 Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE. Refer to instruction manual Warning: explosive material 1. SAFETY Wear eye protection Warning: corrosive substance Wear protective gloves Warning: electricity Protect from rain Use in well ventilated areas Keep away from sources of ignition: battery could explode 1.1. ELECTRICAL SAFETY ‰‰ WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following: You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a Residual Current Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a supply which is not protected by a RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer. 1.1.1. You must also read and understand the following instructions concerning electrical safety. 1.1.2. The Electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a qualified electrician, using a Portable Appliance Tester (PAT), at least once a year. 1.1.3. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician. 1.1.4. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2. and use a Portable Appliance Tester. 1.1.5. Ensure that cables are always protected against short circuit and overload. 1.1.6. Regularly inspect power supply leads, plugs for wear and damage and power connections, to ensure that none is loose or damaged. 1.1.7. Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct fuse - see fuse rating in these instructions. 88 DO NOT pull or carry the appliance by the power cable. 88 DO NOT pull the plug from the socket by the cable. 88 DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a qualified electrician. 1.1.8. This product requires a 16Amp 3 pin plug. (Not supplied) If the cable or plug is damaged during use, switch the electricity supply off and remove from use. Ensure that repairs are carried out by a qualified electrician. If in doubt contact a qualified electrician. A) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'. B) Connect the BROWN live wire to the live terminal 'L'. C) Connect the BLUE neutral wire to the neutral terminal 'N'. D) After wiring check there are no bare wires, that all wires have been correctly connected, that the cable outer insulation is clamped by the cable grip and that the grip is tight. Recommended fuse rating: 16A Sealey recommend that repairs are carried out by a qualified electrician. If an extension reel is used it should be fully unwound before connection. We recommend the use of 2.5mm² section cable. 1.2. GENERAL SAFETY ▲▲ DANGER! BE AWARE, LEAD-ACID BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS REASON, IT VERY IMPORTANT TO READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY, EACH TIME YOU USE THE CHARGING EQUIPMENT. 99 Follow these instructions and those published by the battery and vehicle manufacturers, and the maker of any equipment you intend to use in the vicinity of the battery. Remember to review warning marks on all products and on engines. ‰‰ WARNING! Modern vehicles contain extensive electronic systems. You are required to check with the vehicle manufacturer, for any specific instructions regarding the use of this type of equipment on each vehicle. 99 No liability will be accepted for damage / injury, where this product is not used in accordance with all instructions. © Jack Sealey Limited Original Language Version sUPERBOOST SERIES: 180.V5, 200.V4 Issue 1 10/11/17

  • 1
  • 2
  • 3
  • 4
INSTRUCTIONS FOR
SUPERBOOST STARTER / CHARGER
MODEL NOS:
SUPERBOOST 180.V5 &SUPERBOOST 200.V4
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
1. SAFETY
1.1.
ELECTRICAL SAFETY
±
WARNING!
It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any
other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate
safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend
that a Residual Current Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into
a supply which is not protected by a RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current
Device by contacting your Sealey dealer.
1.1.1.
You must also read and understand the following instructions concerning electrical safety.
1.1.2.
The
Electricity at Work Act 1989
requires that all portable electrical appliances, if used on business premises, are tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.3.
The
Health & Safety at Work Act 1974
makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators.
If in any doubt about electrical safety, contact a qualified electrician.
1.1.4.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2. and
use a Portable Appliance Tester.
1.1.5.
Ensure that cables are always protected against short circuit and overload.
1.1.6.
Regularly inspect power supply leads, plugs for wear and damage and power connections, to ensure that none is loose or damaged.
1.1.7.
Important
: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct
fuse - see fuse rating in these instructions.
8
DO NOT
pull or carry the appliance by the power cable.
8
DO NOT
pull the plug from the socket by the cable.
8
DO NOT
use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or
replaced immediately by a qualified electrician.
1.1.8.
This product requires a 16Amp 3 pin plug. (Not supplied)
If the cable or plug is damaged during use, switch the electricity supply off and remove from use.
Ensure that repairs are carried out by a qualified electrician.
If in doubt contact a qualified electrician.
A) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
B) Connect the BROWN live wire to the live terminal ‘L’.
C) Connect the BLUE neutral wire to the neutral terminal ‘N’.
D) After wiring check there are no bare wires, that all wires have been correctly connected, that the cable
outer insulation is clamped by the cable grip and that the grip is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
If an extension reel is used it should be fully unwound before connection. We recommend the use of 2.5mm² section cable.
1.2.
GENERAL SAFETY
▲
DANGER! BE AWARE, LEAD-ACID BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION.
FOR THIS REASON, IT VERY IMPORTANT TO READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY, EACH TIME YOU USE
THE CHARGING EQUIPMENT.
9
Follow these instructions and those published by the battery and vehicle manufacturers, and the maker of any equipment you intend to
use in the vicinity of the battery. Remember to review warning marks on all products and on engines.
±
WARNING!
Modern vehicles contain extensive electronic systems.
You are required to check with the vehicle manufacturer, for any specific instructions regarding the use of this type of equipment on
each vehicle.
9
No liability will be accepted for damage / injury, where this product is not used in accordance with all instructions.
Original Language Version
© Jack Sealey Limited
Wear
protective
gloves
Warning:
electricity
Protect
from
rain
Use in
well
ventilated
areas
Keep away
from sources
of ignition:
battery could
explode
Refer to
instruction
manual
Warning:
explosive
material
Wear eye
protection
Warning:
corrosive
substance
Recommended fuse
rating:
16A
SUPERBOOST SERIES: 180.V5, 200.V4
Issue 1 10/11/17