Sharp AR-162 AR-162 AR-163 Operation Manual - Page 58

Using the SPF

Get Sharp AR-162 PDF manuals and user guides View all Sharp AR-162 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

SINGLE PASS FEEDER (AR-SP2) Using the SPF q Be sure to remove any staples or paper clips from the originals. q Damaged or crumpled originals may misfeed in the SPF. It is recommended that these originals be copied from the original table. q Before placing curled or wavy originals into the document feeder tray, be sure to flatten them. If not, original misfeeds may result. q For best feeding of originals which have binding holes punched into them, insert them so that the holes are positioned to the right or along the side guides. q Special originals such as transparency film and tracing paper should not be fed through the SPF but should be copied from the original table. Single pass feeder (AR-SP2) OPTIONAL EQUIPMENT Stream feeding mode If the stream feeding mode has been enabled using user program No. 4, the SPF indicator will continue to blink for approximately 5 seconds after feeding of all originals is completed. While this indicator is blinking, any new originals placed in the SPF will be fed and copied automatically. See page 35, USER PROGRAMS. 1 Ensure that no original is left on the original table. 2 Adjust the original guides to the size of the originals. 3 Set the originals face up in the document feeder tray. q The SPF indicator will light up. If this indicator does not light up, the originals are not properly set or the SPF is not properly closed. 4 Ensure that the copy paper size in the paper tray is the same size as the originals. q If an optional paper feed unit is installed, a paper tray with the corresponding paper size will be automatically selected. 56 5 Press the START ( ) key. q Since only one copy per original can be made, the number of copies cannot be changed. However, if an optional electronic sorting kit is installed, a multiple number of copies can be set using the numeric keys. q In some regions, the copier is equipped with a 1page memory buffer. The number of copies can be specified even if an optional electronic sorting kit is not installed. q While making copies from the SPF, do not place originals of the next copying job. Place them after all copies of the current job have been output. q Press the CLEAR ( ) key to stop copying in the middle of a run.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
56
OPTIONAL EQUIPMENT
SINGLE PASS FEEDER (AR-SP2)
Using the SPF
●
Be sure to remove any staples or paper clips from the
originals.
●
Damaged or crumpled originals may misfeed in the SPF.
It is recommended that these originals be copied from the
original table.
●
Before placing curled or wavy originals into the document
feeder tray, be sure to flatten them. If not, original misfeeds
may result.
●
For best feeding of originals which have binding holes
punched into them, insert them so that the holes are
positioned to the right or along the side guides.
●
Special originals such as transparency film and tracing
paper should not be fed through the SPF but should be
copied from the original table.
1
Ensure that no original is left on the original table.
2
Adjust the original guides to the size of the originals.
3
Set the originals face up in the document feeder tray.
●
The SPF indicator will light up. If this indicator does not light up, the
originals are not properly set or the SPF is not properly closed.
4
Ensure that the copy paper size in the paper tray is the
same size as the originals.
●
If an optional paper feed unit is installed, a paper tray with the
corresponding paper size will be automatically selected.
5
Press the START (
) key.
●
Since only one copy per original can be made, the number of copies
cannot be changed. However, if an optional electronic sorting kit is
installed, a multiple number of copies can be set using the numeric
keys.
●
In some regions, the copier is equipped with a 1-
page memory buffer. The number of copies can be
specified even if an optional electronic sorting kit is
not installed.
●
While making copies from the SPF, do not place
originals of the next copying job. Place them after all
copies of the current job have been output.
●
Press the CLEAR (
) key to stop copying in the middle of a run.
Single pass feeder (AR-SP2)
Stream feeding mode
If the stream feeding mode has been enabled using user program
No. 4, the SPF indicator will continue to blink for approximately
5 seconds after feeding of all originals is completed. While this
indicator is blinking, any new originals placed in the SPF will be
fed and copied automatically. See page 35, USER PROGRAMS.