Sharp BD-HP35U BD-HP35U Operation Manual - Page 59

PC control of the Player - wireless problems

Get Sharp BD-HP35U PDF manuals and user guides
UPC - 074000355033
View all Sharp BD-HP35U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Appendix PC control of the Player • This player can be controlled from a PC using the IP. • Use an ETHERNET cable (commercially available) or wireless LAN USB adapter for the connections. NOTE • This operation system should be used by a person who is accustomed to using computers. Communication conditions for IP Connect to the player with the following settings made for IP on the PC. IP protocol: Host IP address: Service: TCP port#: TCP/IP Set the IP address on the player menu None (Do not select Telnet or SSH) Set a port number on the player menu When you set your ID and password on the player menu, you need to enter them as soon as you connect to the player. NOTE • The connection will be cut off when there has been no communication for 3 minutes. IP Control Setup Command format Eight ASCII codes eCR C1 C2 C3 C4 P1 P2 P3 P4 1 Press a/b to select "Settings", then press d or ENTER. 2 Press a/b to select "Communicatioin Setup", then press ENTER. 3 Press a/b to select "IP Control Setup", then press ENTER. 4 Press a/b to select "Change", then press ENTER. 5 To use IP Control, select "Enable", then press ENTER. 6 Set the device name. 7 Set your login ID and password. 8 Set the port to use with IP Control. 9 Confirm the settings, then press "OK". Communication procedure Send the control commands from the PC via the IP. This Player operates according to the received command and sends a response message to the PC. Do not send multiple commands at the same time. Wait until the PC receives the OK response before sending the next command. Make sure to send "A" with the carriage return and confirm that "ERR" returns before operating. Command 4-digits Parameter Return code 4-digits Command 4-digits: Command. The text of four characters. Parameter 4-digits: Parameter 0 - 9, blank Parameter Input the parameter values, aligning left, and fill with blank(s) for the remainder. (Be sure that four values are input for the parameter.) When the input parameter is not within an adjustable range, "ERR" returns. (Refer to "Response code format".) Response code format Normal response OK Return code (0DH) Problem response (communication error or incorrect command) ERR Return code (0DH) Appendix 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
57
Appendix
•
This player can be controlled from a PC using the
IP.
•
Use an ETHERNET cable (commercially available)
or wireless LAN USB adapter for the connections.
NOTE
•
This operation system should be used by a person who
is accustomed to using computers.
Communication conditions for IP
Connect to the player with the following settings
made for IP on the PC.
IP protocol:
TCP/IP
Host IP address:
Set the IP address on the player
menu
Service:
None (Do not select Telnet or
SSH)
TCP port#:
Set a port number on the player
menu
When you set your ID and password on the player
menu, you need to enter them as soon as you
connect to the player.
NOTE
•
The connection will be cut off when there has been no
communication for 3 minutes.
IP Control Setup
1
Press
a/b
to select “Settings”, then press
d
or
ENTER
.
2
Press
a/b
to select “Communicatioin Setup”,
then press
ENTER
.
3
Press
a/b
to select “IP Control Setup”, then
press
ENTER
.
4
Press
a/b
to select “Change”, then press
ENTER
.
5
To use IP Control, select “Enable”, then press
ENTER
.
6
Set the device name.
7
Set your login ID and password.
8
Set the port to use with IP Control.
9
Confirm the settings, then press “OK”.
Communication procedure
Send the control commands from the PC via the IP.
This Player operates according to the received
command and sends a response message to the
PC.
Do not send multiple commands at the same time.
Wait until the PC receives the OK response before
sending the next command.
Make sure to send “A” with the carriage return and
confirm that “ERR” returns before operating.
Command format
Eight ASCII codes eCR
C1 C2 C3 C4 P1 P2 P3
P4
Command
4-digits
Parameter
4-digits
Return code
Command 4-digits: Command. The text of four
characters.
Parameter 4-digits: Parameter 0 – 9, blank
Parameter
Input the parameter values, aligning left, and fill with
blank(s) for the remainder. (Be sure that four values
are input for the parameter.)
When the input parameter is not within an adjustable
range, “ERR” returns. (Refer to “Response code
format”.)
Response code format
Normal response
O
K
Return code (0DH)
Problem response (communication error or
incorrect command)
E
R
R
Return code (0DH)
Appendix
PC control of the Player