Sharp LC-70LE650U Operation Manual - Page 56

Appendix Troubleshooting Problem Possible Solution • No power • Check if you pressed POWER on the remote control unit. Page 14 • Is the AC cord disconnected? Page 7 • Has the power been turned on? Page 14 • Unit cannot be operated. • External influences such as lightning, static electricity, may cause improper operation. In this case, operate the unit after first turning off the power of the TV or unplugging the AC cord and replugging it in after 1 or 2 minutes. • Remote control unit does not operate. • Is the equipment to be operated by the remote control unit set correctly? Press TV to set the remote control unit to the setting for operating the TV. • Are batteries inserted with polarity (e, f) aligned? Page 8 • Are batteries worn out? (Replace with new batteries.) • Are you using it under strong or fluorescent lighting? • Is a fluorescent light illuminated near the remote control sensor? • Is "RC Control Lock" selected in "Operation Lock Out"? Page 25 • Picture is cut off/with sidebar screen. • Is the image position correct? Pages 25 and 42 • Are screen mode adjustments such as picture size made correctly? Pages 18 and 19 • Strange color, light color, or color misalignment • Adjust the picture tone. Pages 22 and 23 • Is the room too bright? The picture may look dark in a room that is too bright. • Power is suddenly turned off. • Is the sleep timer set? Page 17 • Check the power control settings. Page 24 • The unit's internal temperature has increased. Remove any objects blocking vent or clean. • No picture • Is connection to other components correct? Pages 11 to 13 and 39 • Is the correct input selected? Pages 11 and 16 • Is "On" selected in "Audio Only"? Page 24 • If the PC image is not displayed, check the following: - When connecting a laptop PC to the TV, check that display output mode of the PC is set to external monitor. - Check the resolution setting on the PC. Is a non-compatible signal being input? Page 43 • Picture quality of HD programs is poor. • To enjoy HD images from external equipment, you are required to set up HDMI connection or component connection. • If the program content is not of HD quality, HD images cannot be displayed. Check that the program you are viewing provides HD images. • The HD cable/satellite set-top box may need to be configured to output HD images via cable/satellite. • The cable/satellite broadcast may not support a signal resolution of 1080p. • The TV sometimes makes a cracking sound. • This is not a malfunction. This happens when the cabinet slightly expands and contracts according to change in temperature. This does not affect the TV's performance. • The AQUOS ADVANTAGE LIVE cannot be displayed. • Is the ETHERNET cable connected correctly? Page 44 • Check the settings of "Internet Setup". Pages 44 to 45 • Some Internet • The TV has only limited functions compared with regular PC browsers. functions used on a PC are not available from the TV. Page 46 Problem • No sound Possible Solution • Is connection to other components correct? Pages 11 to 13 and 39 • Is the volume too low? Page 16 • Is "Variable" selected in "Output Select"? Page 25 • Have you pressed MUTE on the remote control unit? Page 16 • Check the audio output of the connected external equipment. Is the volume too low or muted? • When external equipment is connected via an HDMI cable, you may need to configure the audio to be output through the HDMI cable. • When audio is not output from external equipment connected to the PC IN or HDMI IN 2 terminal, check the "Audio Select" setting. Page 42 • Even when external equipment is connected using an HDMI-certified cable, an audio cable connection may be required depending on the type of equipment and the media being played back. In this case, in addition to connecting an HDMI-certified cable to the HDMI IN 2 terminal, connect a Ø 3.5 mm stereo minijack cable to the AUDIO IN terminal and set "Audio Select" to "HDMI+Analog". Page 42 • When connecting a PC via an HDMI-certified cable, check the following: - Is the audio output of the PC configured correctly? Check the audio output settings and output audio format in Sound Properties on the PC. The audio formats compatible with this TV are PCM, Dolby Digital and DTS. With other formats, audio cannot be output. - Depending on the board, only video signals may be output. In this case, in addition to connecting an HDMI-certified cable to the HDMI IN 2 terminal, connect a Ø 3.5 mm stereo minijack cable to the AUDIO IN terminal and set "Audio Select" to "HDMI+Analog". Page 42 • If you are using a DVI-HDMI conversion cable to connect external equipment to the TV, check the following: - Is an audio cable connected? The DVI-HDMI conversion cable is for video only. Connect a Ø 3.5 mm stereo minijack cable to listen to the audio. - Is HDMI IN 2 being used? When the TV is connected to another HDMI IN terminal, the audio and video are not output together even if a Ø 3.5 mm stereo minijack cable is connected to the shared AUDIO IN terminal for PC IN and HDMI IN 2. - Check the "Audio Select" setting. Set "Audio Select" to "HDMI+Analog". Page 42 Troubleshooting - 3D Images (for the LE857U, LE757U, LE755U and LE657U models) Problem Possible Solution • 3D images are not displayed. • Is "3D Auto Change" set to "Off"? Press 3D to switch to 3D mode. Page 31 • If "3D Auto Change" is set to "Mode 1" or "Mode 2" but no 3D images are displayed, check the display format of the content being viewed. Some 3D image signals may not be recognized as 3D images automatically. Press 3D to select the appropriate display format for the 3D image. Pages 31 to 32 • Is the power of the 3D Glasses turned on? • Are the 3D Glasses set to 2D mode? For further details, refer to the operation manual of your 3D Glasses. 54