Sharp PN-E803 PN-E803 Operation Manual - Page 17

Disabling power on/off operations, Turning Power On/Off, Mode setting, Date/time setting

Get Sharp PN-E803 PDF manuals and user guides View all Sharp PN-E803 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Turning Power On/Off nMode setting When the monitor is turned on for the first time after being shipped from the factory, the mode setting screen will be displayed. (1)Press or to select YES or NO. (2)Press . ENTER YES: • STANDBY MODE is set to LOW POWER. • Compared to when set to STANDARD, the current consumption is reduced while the monitor is in standby mode/input signal waiting mode, but the startup/return time from standby mode/input signal waiting mode becomes longer. • While the monitor is in standby mode, control via LAN will be disabled. • While the monitor is in standby mode/input signal waiting mode, only certain RS-232C commands can be used. • Depending on the input signal, the monitor may not switch to input signal waiting mode and may not return from input signal waiting mode. NO: • STANDBY MODE is set to STANDARD. • Compared to when set to LOW POWER, the startup/ return time from standby mode/input signal waiting mode is reduced, but more power will be consumed in standby mode/input signal waiting mode. nDate/time setting • If the time has yet to be set when the monitor is first turned on, the date/time setting screen appears. Set the date and time. DATE/TIME SETTING // : : 01 / 01 / 20 15 12 : 00 AM OK···[ENTER] CANCEL···[RETURN] 1. Press or to select the date and time, and press or to change the numerical values. 2. Press ENTER . • Be sure to set the date and time. • The date/time setting screen will close automatically if no operation is performed for about 15 seconds. The date and time can be set using DATE/TIME SETTING from the SETUP menu when the date/time setting screen disappears. TIPS • Set the date in "Month/Day/Year" order. • Set the time on a 12-hour basis. • The clock is maintained by the internal battery. • If you already set the time but the date/time setting screen appears when the power is turned on, the internal battery may be exhausted. Please contact an authorized SHARP servicing dealer or service center for assistance with battery replacement. • Estimated service life of the internal battery: About 5 years (depending on monitor operation) • The initial battery was inserted at the factory when the monitor was shipped, so it may run out of power before its expected operation life. Disabling power on/off operations Power on/power off operations can be disabled in order to protect the monitor from an accidental power off. Set the ADJUSTMENT LOCK in FUNCTION menu to "ON 2". (See page 32.) 17 E

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
17
E
Turning Power On/Off
n
Mode setting
When the monitor is turned on for the first time after being
shipped from the factory, the mode setting screen will be
displayed.
(1)Press
or
to select YES or NO.
(2)Press
ENTER
.
YES:
•
STANDBY MODE is set to LOW POWER.
•
Compared to when set to STANDARD, the current
consumption is reduced while the monitor is in standby
mode/input signal waiting mode, but the startup/return time
from standby mode/input signal waiting mode becomes
longer.
•
While the monitor is in standby mode, control via LAN will
be disabled.
•
While the monitor is in standby mode/input signal waiting
mode, only certain RS-232C commands can be used.
•
Depending on the input signal, the monitor may not switch
to input signal waiting mode and may not return from input
signal waiting mode.
NO:
•
STANDBY MODE is set to STANDARD.
•
Compared to when set to LOW POWER, the startup/
return time from standby mode/input signal waiting mode
is reduced, but more power will be consumed in standby
mode/input signal waiting mode.
n
Date/time setting
•
If the time has yet to be set when the monitor is first turned
on, the date/time setting screen appears. Set the date and
time.
DATE/TIME SETTING
/
/
OK···[ENTER]
CANCEL···[RETURN]
:
:
01
01
15
/
12
AM
00
:
/ 20
1. Press
or
to select the date and time, and
press
or
to change the numerical values.
2. Press
ENTER
.
•
Be sure to set the date and time.
•
The date/time setting screen will close automatically if
no operation is performed for about 15 seconds. The
date and time can be set using DATE/TIME SETTING
from the SETUP menu when the date/time setting screen
disappears.
TIPS
•
Set the date in “Month/Day/Year” order.
•
Set the time on a 12-hour basis.
•
The clock is maintained by the internal battery.
•
If you already set the time but the date/time setting
screen appears when the power is turned on, the
internal battery may be exhausted. Please contact an
authorized
SHARP
servicing dealer or service center for
assistance with battery replacement.
•
Estimated service life of the internal battery: About 5
years (depending on monitor operation)
•
The initial battery was inserted at the factory when the
monitor was shipped, so it may run out of power before
its expected operation life.
Disabling power on/off operations
Power on/power off operations can be disabled in order to
protect the monitor from an accidental power off. Set the
ADJUSTMENT LOCK in FUNCTION menu to “ON 2”. (See
page 32.)