Sharp UX-600M UX-600M Operation Manual - Page 68

Optional Hookup Settings

Get Sharp UX-600M PDF manuals and user guides View all Sharp UX-600M manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

Chapter 7 Answering Machine Hookup Optional Hookup Settings If necessary, you can use the following settings to improve the response of the answering machine hookup to incoming calls. Quiet Detect Time This function causes the fax machine to take over the line and begin reception if a certain duration of silence is detected after the answering machine answers. Time selections for the period of silence are one to ten seconds. Quiet Detect Time has been set to four seconds at the factory. This gives the best performance with most answering machines; however, you may need to adjust this setting depending on the disconnect time of your answering machine. ♦ Some answering machines may have unusually fast disconnect times (equal to or very slightly less than four seconds), which means that the answering machine may disconnect the line before fax reception can begin. In this case, try a Quiet Detect Time setting of three seconds. ♦ If the fax machine is interrupting callers before they can leave a message, try a longer Quiet Detect Time setting. If your outgoing message includes a period of silence, make sure that the setting is longer than that period of silence, or re-record your outgoing message to shorten the silence. To change the Quiet Detect Time setting, follow the steps below. Note: Quiet Detect Time can be turned off by entering "00" for the time. Note, however, that the fax machine will not be able to receive manually dialed faxes. 1 Press the FUNCTION key and then the FUNCTION "4" key. OPTION SETTING will appear 4 in the display. * 2 Press the " " key nine times. QUIET DETECT TM. will appear in the display. 56

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Optional Hookup Settings
If necessary, you can use the following settings to improve the response of the
answering machine hookup to incoming calls.
Quiet Detect Time
This function causes the fax machine to take over the line and begin reception if
a certain duration of silence is detected after the answering machine answers.
Time selections for the period of silence are one to ten seconds. Quiet Detect
Time has been set to four seconds at the factory. This gives the best perform-
ance with most answering machines; however, you may need to adjust this set-
ting depending on the disconnect time of your answering machine.
♦
Some answering machines may have unusually fast disconnect times (equal
to or very slightly less than four seconds), which means that the answering
machine may disconnect the line before fax reception can begin. In this
case, try a Quiet Detect Time setting of three seconds.
♦
If the fax machine is interrupting callers before they can leave a message,
try a longer Quiet Detect Time setting. If your outgoing message includes a
period of silence, make sure that the setting is longer than that period of si-
lence, or re-record your outgoing message to shorten the silence.
To change the Quiet Detect Time setting, follow the steps below.
Note:
Quiet Detect Time can be turned off by entering "00" for the time.
Note, however, that the fax machine will not be able to receive manually di-
aled faxes.
1
Press the
FUNCTION
key and then the
"
4
" key. OPTION SETTING will appear
in the display.
2
Press the "
" key nine times.
QUIET DETECT TM. will appear in
the display.
FUNCTION
4
Chapter 7
Answering Machine Hookup
56