Singer 9970 Instruction Manual - Page 7

Removable Extension, Table, Changing The Presser - accessories

Get Singer 9970 PDF manuals and user guides View all Singer 9970 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

REMOVABLE EXTENSION TABLE A. REMOVING THE EXTENSION TABLE Hook your finger to the left bottom side of the removable extension table and slide it to the left. To attach, insert to the right. B. OPENING THE ACCESSORY CASE Hook your finger to the left side of accessory case and pull toward you. CHANGING THE PRESSER FOOT The presser foot must be changed according to the stitch you sew, or work you do. CAUTION: To prevent accidents. Turn off the power switch before you change the presser foot. A. CHANGING THE PRESSER FOOT 1. Turn the hand wheel toward you until the needle is at its highest point. 2. Raise the presser foot lifter. 3. Remove the presser foot by pushing the presser foot release lever toward you. 4. Place desired foot with its pin directly under the slot in presser foot holder. 5. Lower the presser foot lifting lever and the presser foot will snap into place. B. REMOVING THE PRESSER FOOT HOLDER When attaching presser feet that have their own shank, or when cleaning the machine, you should remove the presser foot holder. 1. Remove the presser foot. 2. Loosen the presser foot thumb screw and remove the presser foot holder. 3. To replace the holder, pull up the holder as far as it will go from bottom of presser bar. 4. Tighten the thumb screw. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
7
REMOVABLE EXTENSION
TABLE
A.REMOVING THE EXTENSION TABLE
Hook your finger to the left bottom side of the
removable extension table and slide it to the
left. To attach, insert to the right.
B.OPENING THE ACCESSORY CASE
Hook your finger to the left side of accessory
case and pull toward you.
CHANGING THE PRESSER
FOOT
The presser foot must be changed according to
the stitch you sew, or work you do.
A.CHANGING THE PRESSER FOOT
1.
Turn the hand wheel toward you until the
needle is at its highest point.
2.
Raise the presser foot lifter.
3.
Remove the presser foot by pushing the
presser foot release lever toward you.
4.
Place desired foot with its pin directly under the
slot in presser foot holder.
5.
Lower the presser foot lifting lever and the
presser foot will snap into place.
CAUTION: To prevent accidents.
Turn off the power switch before you change
the presser foot.
B.REMOVING THE PRESSER FOOT
HOLDER
When attaching presser feet that have their own
shank, or when cleaning the machine, you should
remove the presser foot holder.
1.
Remove the presser foot.
2.
Loosen the presser foot thumb screw and
remove the presser foot holder.
3.
To replace the holder, pull up the holder as far
as it will go from bottom of presser bar.
4.
Tighten the thumb screw.