Singer One Instruction Manual 18 - Page 74

Additional, Information, About, Rolled, Hemming, Secure, Thread, Chain, Rosette

Get Singer One PDF manuals and user guides View all Singer One manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

Additional Information About Rolled Hemming • Hold the thread chain when you begin sewing to keep it from curling into the seam. 5.$ 0 • Place a slight tension on the material in the sewing direction and a finer seam finish can be obtained. 4%) • The minimum overedge stitch width that can be obtained for rolled hemming is approximately 1.5mm (1/16 inch) since the cutting width cannot be set below 3.5mm (9/64 inch). To Secure the Rolled Hem Thread Chain • Apply a small drop of liquid seam sealant to the end of the seam. Allow to dry, then cut the chain close to the stitches. Note: Test the liquid seam sealant for color fastness before use. Rosette: Set machine up for 3 - thread wrapped rolled hem stitching. insert wire or fishing line between presser foot & knife. finish one long edge of a 14"x2" piece of fabric.remove wire or line from presser foot.set machine up for 3 - thread overlock (page 61). Set differential feed to 2.0. Sew (gather) other long edge of fabric. Roll fabric into rosette & selure gathered dege. 73

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
Additional
Information
About
Rolled
Hemming
•
Hold
the
thread
chain
when
you
begin
sewing
to
keep
it
from
curling
into
the
seam.
•
Place
a
slight
tension
on
the
material
in
the
sewing
direction
and
a
finer
seam
finish
can
be
obtained.
•
The
minimum
overedge
stitch
width
that
can
be
obtained
for
rolled
hemming
is
approximately
1.5mm
(1/16
inch)
since
the
cutting
width
cannot
be
set
below
3.5mm
(9/64
inch).
To
Secure
the
Rolled
Hem
Thread
Chain
•
Apply
a
small
drop
of
liquid
seam
sealant
to
the
end
of
the
seam.
Allow
to
dry,
then
cut
the
chain
close
to
the
stitches.
Note:
Test
the
liquid
seam
sealant
for
color
fastness
before
use.
Rosette:
Set
machine
up
for
3
-
thread
wrapped
rolled
hem
stitching.
insert
wire
or
fishing
line
between
presser
foot
&
knife.
finish
one
long
edge
of
a
14"x2"
piece
of
fabric.remove
wire
or
line
from
presser
foot.set
machine
up
for
3
-
thread
overlock
(page
61).
Set
differential
feed
to
2.0.
Sew
(gather)
other
long
edge
of
fabric.
Roll
fabric
into
rosette
&
selure
gathered
dege.
5
.
$
0
4%)
73