Singer SEQS-6700 FUTURA QUARTET Instruction Manual - Page 36

Preparation For Embroidery Sewing

Get Singer SEQS-6700 FUTURA QUARTET PDF manuals and user guides View all Singer SEQS-6700 FUTURA QUARTET manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

3. PREPARATION FOR EMBROIDERY SEWING BEFORE ATTACHING EMBROIDERY UNIT ATTACHING EMBROIDERY FOOT Always be sure to turn off power to machine CAUTION before changing presser foot. Foot holder Screw * Raise presser foot lifter. * Turn the hand wheel counter clockwise (toward you) until the needle is in its highest position. 1. Remove presser foot screw, presser foot and foot holder. 2. Attach the embroidery presser foot behind presser bar so that the drive lever is above the needle clamp. Secure it by tightening presser foot screw. 3. Turn hand wheel toward you to move needle up and down, and check that the embroidery presser foot moves up and down together with the needle. Presser bar Presser foot Drive lever Be careful not to touch the needle when CAUTION replacing presser foot. Needle clamp Embroidery presser foot INSERTING THE BOBBIN Refer to page 6. * A large amount of thread is required for embroidering, so be sure to use a full bobbin. NOTE: During the embroidery process, bobbin thread creates lint which gradually accumulates in the bobbin case. It is recommended that the bobbin case is cleaned periodically to keep the machine running its best. See page 56 for information on cleaning the bobbin case. 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
34
Presser foot
Presser bar
Embroidery presser foot
Needle clamp
Drive lever
Screw
Foot holder
3. PREPARATION FOR EMBROIDERY SEWING
BEFORE ATTACHING EMBROIDERY UNIT
ATTACHING EMBROIDERY FOOT
* Raise presser foot lifter.
* Turn the hand wheel counter clockwise (toward you) until
the needle is in its highest position.
1. Remove presser foot screw, presser foot and foot holder.
2. Attach the embroidery presser foot behind presser bar so
that the drive lever is above the needle clamp. Secure it by
tightening presser foot screw.
3. Turn hand wheel toward you to move needle up and down,
and check that the embroidery presser foot moves up and
down together with the needle.
CAUTION
Always be sure to turn off power to machine
before changing presser foot.
CAUTION
Be careful not to touch the needle when
replacing presser foot.
INSERTING THE BOBBIN
Refer to page 6.
* A large amount of thread is required for embroidering, so
be sure to use a full bobbin.
NOTE:
During the embroidery process, bobbin thread creates
lint which gradually accumulates in the bobbin case.
It is recommended that the bobbin case is cleaned
periodically to keep the machine running its best.
See page 56 for information on cleaning the bobbin
case.