Sony CDX-555RF Operating Instructions (English/Español) - Page 6

CD Changer - wiring

Page 6 highlights

Changing the transmitting frequency Because this unit processes CD playback sound through an FM tuner, there may be interference noise during CD playback. In such a case, change the frequency of the modulated RF signal transmitted from the unit. The initial setting is 88.3 MHz. 1 Press (SHUF/REP) for two seconds until frequency appears. 2 Press or repeatedly to select the frequency. Each time you press or , the frequency changes as follows: : 88.3 MHz t 89.9 MHz t 89.7 MHz t 89.5 MHz t 89.3 MHz t 89.1 MHz t 88.9 MHz t 88.7 MHz t 88.5 MHz t 88.3 MHz : 88.3 MHz t 88.5 MHz t 88.7 MHz t 88.9 MHz t 89.1 MHz t 89.3 MHz t 89.5 MHz t 89.7 MHz t 89.9 MHz t 88.3 MHz 3 Press (SHUF/REP) for two seconds. Using on the wireless remote 1 Press (SHUF) for two seconds until frequency appears. 2 Press or repeatedly to select the frequency. 3 Press (SHUF) for two seconds. Notes • When you change the transmitting frequency on the unit, be sure to tune your FM tuner to the newly selected one. • Press u on the wired remote before changing the frequency if the power to the unit is turned off. CD Changer Listening to a CD 1 Turn on the FM tuner of your car audio. 2 Tune in the selected transmitting frequency* with the FM tuner of your car audio. * The frequency of the unit is set to 88.3 MHz at the factory. You can change the frequency. (See "Changing the transmitting frequency" above.) 3 Press u. CD playback starts. 4 Adjust the volume with the volume control on your car audio. All the tracks play from the beginning. Stopping CD play Press (OFF). Notes • When CD playback stops, you may hear some noise from the speakers. To prevent this from happening, turn the volume down before stopping CD playback. • If you turn off the ignition switch of your car without stopping CD playback, it will automatically resume CD playback from where it was stopped when you turn on the ignition switch again. Locating a specific track - Automatic Music Sensor (AMS) During CD playback, push down either side of (AMS) once for each track you wish to skip. To locate previous tracks To locate succeeding tracks 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44

6
CD Changer
Listening to a CD
1
Turn on the FM tuner of your car audio.
2
Tune in the selected transmitting
frequency
*
with the FM tuner of your car
audio.
*
The frequency of the unit is set to 88.3 MHz
at the factory.
You can change the frequency. (See
Changing the transmitting frequency
above.)
3
Press
u
.
CD playback starts.
4
Adjust the volume with the volume
control on your car audio.
All the tracks play from the beginning.
Stopping CD play
Press
(OFF)
.
Notes
• When CD playback stops, you may hear some
noise from the speakers. To prevent this from
happening, turn the volume down before
stopping CD playback.
• If you turn off the ignition switch of your car
without stopping CD playback, it will
automatically resume CD playback from where it
was stopped when you turn on the ignition
switch again.
Locating a specific track
— Automatic Music Sensor (AMS)
During CD playback, push down either
side of
(AMS)
once for each track you
wish to skip.
Changing the transmitting
frequency
Because this unit processes CD playback
sound through an FM tuner, there may be
interference noise during CD playback. In such
a case, change the frequency of the modulated
RF signal transmitted from the unit. The initial
setting is 88.3 MHz.
1
Press
(SHUF/REP)
for two seconds until
frequency appears.
2
Press
or
repeatedly to
select the frequency.
Each time you press
or
,
the frequency changes as follows:
:
88.3 MHz
t
89.9 MHz
t
89.7 MHz
t
89.5 MHz
t
89.3 MHz
t
89.1 MHz
t
88.9 MHz
t
88.7 MHz
t
88.5 MHz
t
88.3 MHz
:
88.3 MHz
t
88.5 MHz
t
88.7 MHz
t
88.9 MHz
t
89.1 MHz
t
89.3 MHz
t
89.5 MHz
t
89.7 MHz
t
89.9 MHz
t
88.3 MHz
3
Press
(SHUF/REP)
for two seconds.
Using on the wireless remote
1
Press
(SHUF)
for two seconds until
frequency appears.
2
Press
or
repeatedly to
select the frequency.
3
Press
(SHUF)
for two seconds.
Notes
• When you change the transmitting frequency on
the unit, be sure to tune your FM tuner to the
newly selected one.
• Press
u
on the wired remote before changing
the frequency if the power to the unit is turned
off.
To locate
succeeding
tracks
To locate
previous
tracks