Sony CDX-CA650X Operating Instructions - Page 18

Adjusting the sound characteristics, Quickly attenuating the sound

Page 18 highlights

Adjusting the sound characteristics You can adjust the bass, treble, balance, and fader. The bass and treble levels can be stored independently for each source. 1 Select the item you want to adjust by pressing (SOUND) repeatedly. Each time you press (SOUND), the item changes as follows: BAS (bass) t TRE (treble) t BAL (left-right) t FAD (front-rear) 2 Adjust the selected item by pressing either side of (SEEK). When adjusting with the rotary commander, press (SOUND) and rotate the VOL control. Note Adjust within 3 seconds after selecting the item. Quickly attenuating the sound (With the rotary commander or the card remote commander) Press (ATT) on the rotary commander or card remote commander. After "ATT-ON" momentarily appears, the "ATT" appears in the display. To restore the previous volume level, press (ATT) again. Changing the sound and display settings - Menu The following items can be set: SET (Set Up) •CLOCK (page 9) •BEEP - to turn the beeps on or off. •RM (Rotary Commander) - to change the operative direction of the controls of the rotary commander. - Select "NORM" to use the rotary commander as the factory-set position. - Select "REV" when you mount the rotary commander on the right side of the steering column. •P.OUT-4.0V/P.OUT-5.5V - to change the pre-out of the power amplifier to 4.0 V or 5.5 V. Selectable only when the unit is turned off. (CDX-CA660X only) Note If the volume is turned up very high when connected to a power amplifier, the sound may be distorted. In this case, set P.OUT to "4.0V." DSPL (Display) •D.INFO (Dual Information) - to display the clock and the play mode at the same time (ON). •M.DSPL (Motion Display) - to select the Motion Display mode from "1," "2," and "OFF." - Select "1" to show decoration lines in the display and activate Demo display. - Select "2" to show decoration lines in the display and deactivate Demo display. - Select "OFF" to deactivate the Motion Display. •A.SCRL (Auto Scroll) - Select "ON" to scroll all automatically displayed names exceeding 8 characters. - When Auto scroll is set to off and the disc/track name is changed, the disc/ track name does not scroll. SND (Sound) •LOUD (Loudness) - to enjoy bass and treble even at low volumes. The bass and treble will be reinforced. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28

18
Changing the sound and
display settings
— Menu
The following items can be set:
SET (Set Up)
•CLOCK (page 9)
•BEEP — to turn the beeps on or off.
•RM (Rotary Commander) — to change the
operative direction of the controls of the
rotary commander.
Select “NORM” to use the rotary
commander as the factory-set position.
Select “REV” when you mount the rotary
commander on the right side of the
steering column.
•P.OUT-4.0V/P.OUT-5.5V — to change the
pre-out of the power amplifier to 4.0 V or
5.5 V. Selectable only when the unit is turned
off. (CDX-CA660X only)
Note
If the volume is turned up very high when
connected to a power amplifier, the sound may be
distorted. In this case, set P.OUT to “4.0V.”
DSPL (Display)
•D.INFO (Dual Information) — to display the
clock and the play mode at the same time
(ON).
•M.DSPL (Motion Display) — to select the
Motion Display mode from “1,” “2,” and
“OFF.”
Select “1” to show decoration lines in the
display and activate Demo display.
Select “2” to show decoration lines in the
display and deactivate Demo display.
Select “OFF” to deactivate the Motion
Display.
•A.SCRL (Auto Scroll)
Select “ON” to scroll all automatically
displayed names exceeding 8 characters.
When Auto scroll is set to off and the
disc/track name is changed, the disc/
track name does not scroll.
SND (Sound)
•LOUD (Loudness) — to enjoy bass and treble
even at low volumes. The bass and treble will
be reinforced.
Adjusting the sound
characteristics
You can adjust the bass, treble, balance, and
fader.
The bass and treble levels can be stored
independently for each source.
1
Select the item you want to adjust by
pressing
(SOUND)
repeatedly.
Each time you press
(SOUND)
, the item
changes as follows:
BAS (bass)
t
TRE (treble)
t
BAL (left-right)
t
FAD (front-rear)
2
Adjust the selected item by pressing
either side of
(SEEK)
.
When adjusting with the rotary
commander, press
(SOUND)
and rotate the
VOL control.
Note
Adjust within 3 seconds after selecting the item.
Quickly attenuating the
sound
(With the rotary commander or the card
remote commander)
Press
(ATT)
on the rotary commander or
card remote commander.
After “ATT-ON” momentarily appears, the
“ATT” appears in the display.
To restore the previous volume level, press
(ATT)
again.