Sony CDX-CA760X Operating Instructions - Page 18

Adjusting the sound characteristics, Quickly attenuating the sound

Get Sony CDX-CA760X - Fm/am Compact Disc Player PDF manuals and user guides View all Sony CDX-CA760X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Adjusting the sound characteristics You can adjust the bass, treble, balance, fader, and subwoofer volume. The bass and treble levels and subwoofer volume can be stored independently for each source. 1 Select the item you want to adjust by pressing (SOUND) repeatedly. Each time you press (SOUND), the item changes as follows: BAS (bass) t TRE (treble) t BAL (left-right) t FAD (front-rear) t SUB (subwoofer volume) 2 Adjust the selected item by pressing either side of (SEEK). When adjusting with the rotary commander, press (SOUND) and rotate the VOL control. Note Adjust within 3 seconds after selecting the item. Quickly attenuating the sound (With the rotary commander or the card remote commander) Press (ATT) on the rotary commander or card remote commander. "ATT on" appears in the display momentarily. To restore the previous volume level, press (ATT) again. Tip When the interface cable of a car telephone is connected to the ATT lead, the unit decreases the volume automatically when a telephone call comes in (Telephone ATT function). Changing the sound and display settings - Menu The following items can be set: Set Up • Clock (page 9) • Beep - to turn the beeps on or off. • RM (Rotary Commander) - to change the operative direction of the controls of the rotary commander. - Select "norm" to use the rotary commander as the factory-set position. - Select "rev" when you mount the rotary commander on the right side of the steering column. • Multi language (language selection) - to change the display language to English, French, or Spanish. • P.Out 4.0V/5.5V- to change the pre-out of the power amplifier to 4.0V or 5.5V. Selectable only when the unit is turned off. (CDXCA760X only) Note If the volume is turned up very high when connected to a power amplifier, the sound may be distorted. In this case, set P.Out to "4.0V." Display • D.Info (Dual Information) - to display the clock and the play mode at the same time (on). Functions only when SA is not set to B-1 - B-5. • SA (Spectrum Analyzer) (page 20) - to change the display pattern of the equalizer display. • M.Dspl (Motion Display) - to select the Motion Display mode from "1," "2," and "off." - Select "1" to show decoration patterns in the display and activate Demo display. - Select "2" to show decoration patterns in the display and deactivate Demo display. - Select "off" to deactivate the Motion Display. The Demo display in the M.Dspl 1 mode will appear about 10 seconds after the unit is turned off. • Dimmer - to change the brightness of the display. - Select "Auto" to dim the display only when you turn the lights on. - Select "on" to dim the display. - Select "off" to deactivate the Dimmer. • Contrast - to adjust the contrast if the indications on the display are not recognizable because of the unit's installation position. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
18
Adjusting the sound
characteristics
You can adjust the bass, treble, balance, fader,
and subwoofer volume.
The bass and treble levels and subwoofer volume
can be stored independently for each source.
1
Select the item you want to adjust by
pressing
(SOUND)
repeatedly.
Each time you press
(SOUND)
, the item
changes as follows:
BAS (bass)
t
TRE (treble)
t
BAL (left-right)
t
FAD (front-rear)
t
SUB (subwoofer volume)
2
Adjust the selected item by pressing
either side of
(SEEK)
.
When adjusting with the rotary commander,
press
(SOUND)
and rotate the VOL control.
Note
Adjust within 3 seconds after selecting the item.
Quickly attenuating the
sound
(With the rotary commander or the card
remote commander)
Press
(ATT)
on the rotary commander
or card remote commander.
“ATT on” appears in the display momentarily.
To restore the previous volume level, press
(ATT)
again.
Tip
When the interface cable of a car telephone is
connected to the ATT lead, the unit decreases the
volume automatically when a telephone call comes in
(Telephone ATT function).
Changing the sound and
display settings
—
Menu
The following items can be set:
Set Up
• Clock (page 9)
• Beep — to turn the beeps on or off.
• RM (Rotary Commander) — to change the
operative direction of the controls of the rotary
commander.
– Select “norm” to use the rotary commander
as the factory-set position.
– Select “rev” when you mount the rotary
commander on the right side of the steering
column.
• Multi language (language selection) — to
change the display language to English,
French, or Spanish.
•
P.Out 4.0V/5.5V— to change the pre-out of the
power amplifier to 4.0V or 5.5V. Selectable
only when the unit is turned off. (CDX-
CA760X only)
Note
If the volume is turned up very high when connected
to a power amplifier, the sound may be distorted. In
this case, set P.Out to “4.0V.”
Display
• D.Info (Dual Information) — to display the
clock and the play mode at the same time (on).
Functions only when SA is not set to B-1 – B-5.
• SA (Spectrum Analyzer) (page 20) — to
change the display pattern of the equalizer
display.
• M.Dspl (Motion Display) — to select the
Motion Display mode from “1,” “2,” and “off.”
– Select “1” to show decoration patterns in the
display and activate Demo display.
– Select “2” to show decoration patterns in the
display and deactivate Demo display.
– Select “off” to deactivate the Motion Display.
The Demo display in the M.Dspl 1 mode will
appear about 10 seconds after the unit is turned
off.
• Dimmer — to change the brightness of the
display.
– Select “Auto” to dim the display only when
you turn the lights on.
– Select “on” to dim the display.
– Select “off” to deactivate the Dimmer.
• Contrast — to adjust the contrast if the
indications on the display are not recognizable
because of the unit’s installation position.