Sony CDX-L600X Operating Instructions - Page 21

Troubleshooting

Get Sony CDX-L600X - Fm/am Compact Disc Player PDF manuals and user guides View all Sony CDX-L600X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Troubleshooting The following checklist will help you remedy problems you may encounter with your unit. Before going through the checklist below, check the connection and operating procedures. General No sound. •Rotate the volume control dial clockwise to adjust the volume. •Cancel the ATT function. •Set the fader control to the center position for a 2-speaker system. The contents of the memory have been erased. •The RESET button has been pressed. t Store again into the memory. •The power cord or battery has been disconnected. •The power connecting cord is not connected properly. No beep sound. The beep sound is cancelled (page 16). Indications disappear from/do not appear in the display. •The clock display disappears if you press (OFF) for 2 seconds. t Press (OFF) again for 2 seconds to display the clock. •Remove the front panel and clean the connectors. See "Cleaning the connectors" (page 18) for details. Stored stations and correct time are erased. The fuse has blown. Makes noise when the ignition key is in the ON, ACC, or OFF position. The leads are not matched correctly with the car's accessory power connector. No power is being supplied to the unit. •Check the connection. If everything is in order, check the fuse. •The car does not have an ACC position. t Press (SOURCE) (or insert a disc) to turn on the unit. The power is continuously supplied to the unit. The car does not have an ACC position. The power antenna does not extend. The power antenna does not have a relay box. CD playback A disc cannot be loaded. •Another CD is already loaded. •The CD is forcibly inserted upside down or in the wrong way. Playback does not begin. •Dirty or defective disc. •CD-R/CD-RW that is not finalized. •You tried to playback a CD-R/CD-RW not designed for audio use. •Some CD-Rs/CD-RWs may not play due to its recording equipment or the disc condition. A disc is automatically ejected. The ambient temperature exceeds 50°C (122°F). The operation buttons do not function. CD will not be ejected. Press the RESET button. The sound skips from vibration. •The unit is installed at an angle of more than 60°. •The unit is not installed in a sturdy part of the car. The sound skips. Dirty or defective disc. continue to next page t 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
21
The power is continuously supplied to the
unit.
The car does not have an ACC position.
The power antenna does not extend.
The power antenna does not have a relay
box.
CD playback
A disc cannot be loaded.
•
Another CD is already loaded.
•
The CD is forcibly inserted upside down or
in the wrong way.
Playback does not begin.
•
Dirty or defective disc.
•
CD-R/CD-RW that is not finalized.
•
You tried to playback a CD-R/CD-RW not
designed for audio use.
•
Some CD-Rs/CD-RWs may not play due
to its recording equipment or the disc
condition.
A disc is automatically ejected.
The ambient temperature exceeds 50
°
C
(122
°
F).
The operation buttons do not function.
CD will not be ejected.
Press the RESET button.
The sound skips from vibration.
•
The unit is installed at an angle of more
than 60
°
.
•
The unit is not installed in a sturdy part of
the car.
The sound skips.
Dirty or defective disc.
Troubleshooting
The following checklist will help you remedy
problems you may encounter with your unit.
Before going through the checklist below,
check the connection and operating
procedures.
General
No sound.
•
Rotate the volume control dial clockwise to
adjust the volume.
•
Cancel the ATT function.
•
Set the fader control to the center position
for a 2-speaker system.
The contents of the memory have been
erased.
•
The RESET button has been pressed.
t
Store again into the memory.
•
The power cord or battery has been
disconnected.
•
The power connecting cord is not
connected properly.
No beep sound.
The beep sound is cancelled (page 16).
Indications disappear from/do not appear in
the display.
•
The clock display disappears if you press
(OFF)
for 2 seconds.
t
Press
(OFF)
again for 2 seconds to
display the clock.
•
Remove the front panel and clean the
connectors. See
“
Cleaning the connectors
”
(page 18) for details.
Stored stations and correct time are erased.
The fuse has blown.
Makes noise when the ignition key is in the
ON, ACC, or OFF position.
The leads are not matched correctly with the
car
’
s accessory power connector.
No power is being supplied to the unit.
•
Check the connection. If everything is in
order, check the fuse.
•
The car does not have an ACC position.
t
Press
(SOURCE)
(or insert a disc) to
turn on the unit.
continue to next page
t