Sony CDX-MP30 Installation/Connection Instructions - Page 1
Sony CDX-MP30 - Fm/am Compact Disc Player Manual
View all Sony CDX-MP30 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
3-241-295-21 (1) FM/AM Compact Disc Player Installation/Connections Installation/Connexions Instalación/Conexiones 2A AUDIO OUT FRONT AUDIO OUT REAR B BUS AUDIO IN BUS CONTROL IN CDX-MP30 Sony Corporation © 2002 Printed in Korea 1 1 TOP 4 2 3 × 4 × 2 5 Equipment used in illustrations (not supplied) Appareils utilisés dans les illustrations (non fournis) Equipo utilizado en las ilustraciones (no suministrado) Front speaker Haut-parleur frontal Altavoz delantero Power amplifier Amplificateur de puissance Amplificador de potencia Rear speaker Haut-parleur arrière Altavoz trasero CD/MD changer Changeur de CD/MD Cambiador de CD/MD Rotary commander RM-X4S Satellite de commande RM-X4S Mando rotativo RM-X4S BUS AUDIO IN * Source selector Sélecteur de source Selector de fuente BUS CONTROL IN * not supplied non fourni no suministrado Cautions • This unit is designed for negative ground 12 V DC operation only. • Do not get the wires under a screw, or caught in moving parts (e.g. seat railing). • Before making connections, turn the car ignition off to avoid short circuits. • Connect the yellow and red power input leads only after all other leads have been connected. • Run all ground wires to a common ground point. • Be sure to insulate any loose unconnected wires with electrical tape for safety. • The use of optical instruments with this product will increase eye hazard. Notes on the power supply cord (yellow) • When connecting this unit in combination with other stereo components, the connected car circuit's rating must be higher than the sum of each component's fuse. • When no car circuits are rated high enough, connect the unit directly to the battery. Parts Iist (1) The numbers in the list are keyed to those in the instructions. Caution Handle the bracket 1 carefully to avoid injuring your fingers. TOP Connection example (2) Notes (2-B) • Be sure to connect the ground cord before connecting the amplifier. • If you connect an optional power amplifier and do not use the built-in amplifier, the beep sound will be deactivated. Connection diagram (3) 1 To a metal surface of the car First connect the black ground lead, then connect the yellow and red power input leads. 2 To the power antenna control lead or power supply lead of antenna booster amplifier Notes • It is not necessary to connect this lead if there is no power antenna or antenna booster, or with a manually-operated telescopic antenna. • When your car has a built-in FM/AM antenna in the rear/side glass, see "Notes on the control and power supply leads." 3 To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers. Connecting any other system may damage the unit. 4 To the interface cable of a car telephone 5 To the +12 V power terminal which is energised in the accessory position of the ignition key switch Notes • If there is no accessory position, connect to the +12 V power (battery) terminal which is energised at all times. Be sure to connect the black ground to it first. • When your car has a built-in FM/AM antenna in the rear/side glass, see "Notes on the control and power supply leads." 6 To the +12 V power terminal which is energised at all times Be sure to connect the black ground lead to it first. Notes on the control and power supply leads • The power antenna control lead (blue) supplies +12 V DC when you turn on the tuner. • When your car has built-in FM/AM antenna in the rear/side glass, connect the power antenna control lead (blue) or the accessory power input lead (red) to the power terminal of the existing antenna booster. For details, consult your dealer. • A power antenna without relay box cannot be used with this unit. Memory hold connection When the yellow power input lead is connected, power will always be supplied to the memory circuit even when the ignition key is turned off. Notes on speaker connection • Before connecting the speakers, turn the unit off. • Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to avoid its damage. • Do not connect the speaker terminals to the car chassis, or connect the terminals of the right speakers with those of the left speaker. • Do not connect the ground lead of this unit to the negative (-) terminal of the speaker. • Do not attempt to connect the speakers in parallel. • Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speaker terminals may damage the unit. • To avoid a malfunction, do not use the built-in speaker wires installed in your car if the unit shares a common negative (-) lead for the right and left speakers. • Do not connect the unit's speaker cords to each other.