Sony CMT-HPX9 Operating Instructions - Page 31

Specifications, Additional Information - parts

Get Sony CMT-HPX9 - Micro Hi Fi Component System PDF manuals and user guides View all Sony CMT-HPX9 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

To save a tape permanently To prevent a tape from being accidentally recorded over, break off the cassette tab from side A or B as illustrated. Break off the cassette tab If you later want to reuse the tape for recording, cover the broken tab with adhesive tape. Before placing a cassette in the tape deck Take up any slack in the tape. Otherwise, the tape may get entangled in the parts of the tape deck and become damaged. When using a tape longer than 90 minutes The tape is very elastic. Do not change the tape operations such as play, stop, and fast-winding frequently. The tape may get entangled in the tape deck. Cleaning the tape heads Clean the tape heads after every 10 hours of use. Be sure to clean the tape heads before you start an important recording or after playing an old tape. Use a separately sold dry-type or wet-type cleaning cassette. For details, refer to the instructions of the cleaning cassette. Demagnetizing the tape heads Demagnetize the tape heads and the metal parts that have contact with the tape after every 20 to 30 hours of use with a separately sold demagnetizing cassette. For details, refer to the instructions of the demagnetizing cassette. Specifications Main unit (HCD-HPX10W/HCD-HPX9/ HCD-HPX7) Amplifier section For the United States model AUDIO POWER SPECIFICATIONS HCD-HPX10W POWER OUTPUT AND TOTAL HARMONIC DISTORTION: With 6-ohm loads, both channels driven, from 120 - 10,000 Hz: rated 55 watts per channel minimum RMS power, with no more than 10% total harmonic distortion from 250 milliwatts to rated output. HCD-HPX9 POWER OUTPUT AND TOTAL HARMONIC DISTORTION: With 6-ohm loads, both channels driven, from 120 - 10,000 Hz: rated 75 watts per channel minimum RMS power, with no more than 10% total harmonic distortion from 250 milliwatts to rated output. Additional Information HCD-HPX10W for CMT-HPX10W DIN power output (rated): 50 + 50 W (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 60 + 60 W (6 ohms at 1 kHz, 10% THD) Music power output (reference): 100 + 100 W HCD-HPX9 for CMT-HPX9 North American model: Continuous RMS power output (reference): 80 + 80 W (6 ohms at 1 kHz, 10% Other models: THD) The following measured at AC 240 V, AC 220 V or AC 120 V DIN power output (rated): 53 + 53 W (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 70 + 70 W (6 ohms at 1 kHz, 10% THD) continued 31GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
Additional Information
31
GB
To save a tape permanently
To prevent a tape from being accidentally recorded
over, break off the cassette tab from side A or B as
illustrated.
If you later want to reuse the tape for recording, cover
the broken tab with adhesive tape.
Before placing a cassette in the tape
deck
Take up any slack in the tape. Otherwise, the tape may
get entangled in the parts of the tape deck and become
damaged.
When using a tape longer than
90 minutes
The tape is very elastic. Do not change the tape
operations such as play, stop, and fast-winding
frequently. The tape may get entangled in the tape
deck.
Cleaning the tape heads
Clean the tape heads after every 10 hours of use. Be
sure to clean the tape heads before you start an
important recording or after playing an old tape. Use a
separately sold dry-type or wet-type cleaning cassette.
For details, refer to the instructions of the cleaning
cassette.
Demagnetizing the tape heads
Demagnetize the tape heads and the metal parts that
have contact with the tape after every 20 to 30 hours of
use with a separately sold demagnetizing cassette. For
details, refer to the instructions of the demagnetizing
cassette.
Main unit (HCD-HPX10W/HCD-HPX9/
HCD-HPX7)
Amplifier section
For the United States model
AUDIO POWER SPECIFICATIONS
HCD-HPX10W
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
With 6-ohm loads, both channels driven, from
120 – 10,000 Hz: rated 55 watts per channel
minimum RMS power, with no more than 10%
total harmonic distortion from 250 milliwatts to
rated output.
HCD-HPX9
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
With 6-ohm loads, both channels driven, from
120 – 10,000 Hz: rated 75 watts per channel
minimum RMS power, with no more than 10%
total harmonic distortion from 250 milliwatts to
rated output.
HCD-HPX10W for CMT-HPX10W
DIN power output (rated):
50 + 50 W
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference):
60 + 60 W
(6 ohms at 1 kHz, 10%
THD)
Music power output (reference):
100 + 100 W
HCD-HPX9 for CMT-HPX9
North American model:
Continuous RMS power output (reference):
80 + 80 W
(6 ohms at 1 kHz, 10%
THD)
Other models:
The following measured at AC 240 V, AC 220 V or AC
120 V
DIN power output (rated):
53 + 53 W
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference):
70 + 70 W
(6 ohms at 1 kHz, 10%
THD)
Break off the
cassette tab
Specifications
continued