Sony CPD-E240 Operating Instructions - Page 4

Setup, Adjustments - driver

Page 4 highlights

Setup Adjustments 1 Connecting your monitor to your computer Navigating the menu 1 Press the MENU/OK button to display the main menu. Video signal cable of the monitor to HD15 of the connecting computer MENU , Main menu Connecting to a Macintosh or compatible computer When connecting this monitor to a Macintosh computer, use the Macintosh adapter (not supplied) if necessary. Connect the Macintosh adapter to the computer before connecting the cable. The pin assignment of the HD 15 video signal cable 1 2 345 6 7 8 9 10 11 12 13 14 15 Pin No. Signal Pin No. Signal 1 Red 9 DDC HOST 5V* 2 Green (Sync on 10 Green) 11 Ground ID (Ground) 3 4 Blue ID (Ground) 12 Bi-Directional Data (SDA)* 5 DDC Ground* 13 H. Sync 6 Red Ground 14 V. Sync 7 8 Green Ground 15 Blue Ground Data Clock (SCL)* * DDC (Display Data Channel) is a standard of VESA. 2 Turning on the monitor and computer 1 Connect the power cord to the monitor and press the 1 (power) switch to turn on the monitor. 2 Turn on the computer. No need for specific drivers This monitor complies with the "DDC" Plug & Play standard and automatically detects all the monitor's information. No specific driver needs to be installed to the computer. The first time you turn on your PC after connecting the monitor, the setup Wizard may appear on the screen. In this case, follow the on-screen instructions. The Plug & Play monitor is automatically selected so that you can use this monitor. the resolution of the current input signal (only if the signal matches to one of the recommended VESA timing modes). 68 . 7kHz / 85Hz 1024 768 the horizontal and vertical frequencies of the current input signal 2 Move the joystick m/M to highlight the main menu that you want to adjust and press the MENU/OK button. MENU b Sub menu S I ZE / CENTER 26 3 Move the joystick m/M to highlight the submenu that you want to adjust. Then move the joystick

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24

4
Setup
1
Connecting your monitor to your computer
Connecting to a Macintosh or compatible
computer
When connecting this monitor to a Macintosh computer, use the
Macintosh adapter (not supplied) if necessary. Connect the
Macintosh adapter to the computer before connecting the cable.
The pin assignment of the HD 15 video signal cable
*
DDC (Display Data Channel) is a standard of VESA.
2
Turning on the monitor and computer
1
Connect the power cord to the monitor and press the
1
(power) switch to turn on the monitor.
2
Turn on the computer.
No need for specific drivers
This monitor complies with the
DDC
Plug & Play standard and
automatically detects all the monitor
s information. No specific driver
needs to be installed to the computer.
The first time you turn on your PC after connecting the monitor, the setup
Wizard may appear on the screen. In this case, follow the on-screen
instructions. The Plug & Play monitor is automatically selected so that you
can use this monitor.
Notes
Do not touch the pins of the video signal cable connector.
Check the alignment of the HD15 connector to prevent bending the pins
of the video signal cable connector.
Adjustments
Navigating the menu
1
Press the MENU/OK button to display the main menu.
2
Move the joystick
m
/
M
to highlight the main menu that
you want to adjust and press the MENU/OK button.
3
Move the joystick
m
/
M
to highlight the submenu that
you want to adjust. Then move the joystick
<
/
,
to
make adjustments.
Adjusting the brightness and contrast
Brightness and contrast adjustments are made using a separate
BRIGHTNESS/CONTRAST menu. These adjustments are
effective for all input signals.
1
Move the joystick in any direction to display the
BRIGHTNESS/CONTRAST menu.
2
Move the joystick
m
/
M
to adjust the brightness (
),
and
<
/
,
to adjust the contrast (
).
Note
If you set the brightness and contrast level to
0
, the picture will black out
and no picture will appear.
Video signal cable
of the monitor
to HD15 of the
connecting computer
5
4
3
2
1
6
7
8
9 10
11 12 13 14 15
Pin No.
Signal
1
Red
2
Green (Sync on
Green)
3
Blue
4
ID (Ground)
5
DDC Ground*
6
Red Ground
7
Green Ground
8
Blue Ground
9
DDC HOST 5V*
10
Ground
11
ID (Ground)
12
Bi-Directional
Data (SDA)*
13
H. Sync
14
V. Sync
15
Data Clock
(SCL)*
Pin No.
Signal
,
68.7kHz/
85Hz
1024
768
the horizontal
and vertical
frequencies
of the current
input signal
the resolution of the current
input signal (only if the signal
matches to one of the
recommended VESA timing
modes).
Main menu
MENU
Sub menu
26
S I ZE / CENTER
MENU
b
50
100
BR I GHTNESS / CONTRAST