Sony DCR-TRV50 Network Function Operating Instructions - Page 100

Troubles about the album on the Web, Adjusting the LCD screen (CALIBRATION)

Get Sony DCR-TRV50 - Digital Handycam Camcorder PDF manuals and user guides View all Sony DCR-TRV50 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 100 highlights

Troubleshooting Troubles about the album on the Web The message "DI Customer ID profile Incomplete" is indicated and your camcorder cannot access the album on the Web. c The DI customer ID is required to use the album on the Web. You cannot view or edit your album, send an invitation card, or upload images. (An error code is indicated.) c See "Album error codes" (p. 105). It takes some time to load the album. c When the web site is busy, try to connect through other providers or access points, or connect during off-peak times. The image cannot be deleted. c There may be no images. Tap (Refresh). The image cannot be downloaded. c There may be no images. Tap (Refresh). Adjusting the LCD screen (CALIBRATION) The buttons on the touch panel may not work correctly. If this happens, follow the procedure below. (1) Set the POWER switch to OFF (CHG). (2) Eject the cassette from your camcorder, then disconnect any connecting cable from your camcorder. (3) Set the POWER switch to VCR while pressing DISPLAY/TOUCH PANEL on your camcorder, then keep pressing DISPLAY/TOUCH PANEL for about five seconds. (4) Follow the procedure below using the stylus supplied with your camcorder. 1 Touch at the upper left corner. 2 Touch at the lower right corner. 3 Touch in the middle of the screen. CALIBRATE CALIBRATE CALIBRATE Note If you do not tap the right spot, always returns to the position at the upper left corner. In this case, start from step 4 again. 100

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
100
Troubleshooting
Troubles about the album on the Web
The message “DI Customer ID profile Incomplete” is indicated and your camcorder cannot
access the album on the Web.
c
The DI customer ID is required to use the album on the Web.
You cannot view or edit your album, send an invitation card, or upload images. (An error
code is indicated.)
c
See “Album error codes” (p. 105).
It takes some time to load the album.
c
When the web site is busy, try to connect through other providers or access points, or
connect during off-peak times.
The image cannot be deleted.
c
There may be no images. Tap
(Refresh).
The image cannot be downloaded.
c
There may be no images. Tap
(Refresh).
Adjusting the LCD screen (CALIBRATION)
The buttons on the touch panel may not work correctly. If this happens, follow the
procedure below.
(
1
)
Set the POWER switch to OFF (CHG).
(
2
)
Eject the cassette from your camcorder, then disconnect any connecting cable
from your camcorder.
(
3
)
Set the POWER switch to VCR while pressing DISPLAY/TOUCH PANEL on
your camcorder, then keep pressing DISPLAY/TOUCH PANEL for about five
seconds.
(
4
)
Follow the procedure below using the stylus supplied with your camcorder.
1
Touch
at the upper left corner.
2
Touch
at the lower right corner.
3
Touch
in the middle of the screen.
Note
If you do not tap the right spot,
always returns to the position at the upper left
corner. In this case, start from step 4 again.
CALIBRATE
CALIBRATE
CALIBRATE