Sony DPP-FP90 Read This First (Large File - 18.03 MB) - Page 2

Printing an image You are now ready for printing. Depending on the memory card or external device you use, the printing procedures differ. This leaflet explains how to select and print an image in a memory card. 1 Connect to the AC power source. 1 Insert the plug of the AC adaptor to the DC IN 24 V jack on the back of the printer. 2 Connect one plug of the AC power cord to the plug of the AC adaptor and the other plug to the wall outlet close-by. Install the printer in a location with a 20 cm (13/16 inch) or more space in front and 10 cm (13/32 inch) or more space at the rear. 10 cm (13/32 inch) 20 cm (13/16 inch) AC adaptor To the wall outlet AC power cord  Notes • Do not place the printer in an unstable location such as on a wobble table. • Leave enough room around the printer. The print paper emerges from the back a few times during printing. Keep 10 cm (13/32 inch) or more space at the rear of the printer. • Never move or turn off the printer while it is printing; the ink ribbon or print paper may become stuck. In case you turn off the power, keep the paper tray inserted and turn on the printer. If paper being printed remains in the printer, remove the paper that emerged automatically and resume printing.  Notes on using the AC adaptor • The print paper emerges from the back a few times during printing. Do not block the back of the printer with the AC adaptor or AC power cord. • Connect the AC adaptor to an easily accessible wall outlet close by. If some trouble occurs while using the adaptor, immediately shut off the power by disconnecting the plug from the wall outlet. • Do not short the plug of the AC adaptor with a metallic object, as this may cause malfunction. • Do not use the AC adaptor in a narrow space, such as the one between the printer and the wall. • When you have finished using the AC adaptor, disconnect the AC power cord from the DC IN 24V jack of the printer and from the AC power sources. • The printer is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet , even if the printer itself has been turned off. What you can do with the digital photo printer (See the Operating Instruction for the operations below.) In addition to the basic printing procedures explained in this leaflet, you can make a variety of printing. You can also print an image of an external device connected to the printer. You can make a variety of printing You can use the editing and creative print features of the printer to make the following prints: Easy printing (Index/DPOF/ All)  Page 11 on the Operating Instructions Calendar print  Page 20 on the Operating Instructions Enlarged, reduced, moved, rotated, corrected, specialeffected prints  Pages 12 to 17 on the Operating Instructions Layout print  Page 19 on the Operating Instructions ID Photo print  Page 21 on the Operating Instructions Digital Superimpose print  Page 23 on the Operating Instructions 2 Insert a memory card into the slot. Prepare the desired memory card for printing: "Memory Stick," "Memory Stick Duo", SD card, miniSD card, or CompactFlash card. Insert the memory card into the appropriate slot with its terminal side facing toward the slot. For the types of memory cards you can use with the printer, please see pages 72 to 75 of the supplied operating instructions.  Note Insert the memory card that you want to use for printing only. When multiple memory cards are inserted, the memory card inserted first will have the first priority. When you turn on the printer with multiple memory cards being inserted, the printer detects in the order of "Memory Stick" (or "Memory Stick Duo"), SD card, and CompactFlash card.  The printer supports both the standard and small sizes. A "Memory Stick Duo" adaptor is not necessary. The printer supports both SD and miniSD cards. A miniSD card adaptor is not necessary. Access indicator (Do not remove the memory card while the access indicator flashes.) "Memory Stick", "Memory Stick Duo" CompactFlash card SD card, miniSD card Insert from the terminal side. Insert from the terminal facing down. Insert from the terminal facing down. To eject a memory card Remove the memory card from the slot slowly in the reverse direction as it is inserted.  Note When carrying your printer, make sure to remove the memory card and paper tray. Otherwise, the printer may be damaged. 3 Press the  (on/standby) switch to turn on the printer (  ). An image contained in the memory card is displayed. 4 Select an image for printing (  ). Press / button repeatedly until the image that you want to print appears.  (on/standby)  switch  / buttons  / buttons buttons  AUTO TOUCH-UP button  PRINT button  ENTER button  To set the print quantity (  ) To increase the print quantity: Press  button. To decrease the print quantity: Press  button. To print multiple images Select an image in step 4 and set the print quantity with the above procedures. Repeat this procedure for multiple images. Print quantity 5 Press the PRINT button. While the PRINT button lights in blue green, the printer is ready for printing.  Notes on printing • Do not remove the paper tray during printing. Otherwise, malfunction may occur. • The print paper emerges a few times during printing. Do not touch nor pull the emerged paper. Wait for the print paper to be fully ejected after printing ends. • Do not leave many sheets of the ejected printed paper piled up on the paper tray. Please remove them time to time. Especially when sheets of printed paper are so piled that they are about to drop from the paper tray, remove them in time. • If print paper is jammed.  Page 68 on the Operating Instructions  Notes on using a memory card • Do not attempt to insert a memory card forcibly into or out of the slot. If you do so, the memory card or the printer may be damaged. • Do not remove the memory card while the access indicator flashes or accessing dialog box is displayed on the LCD screen of the printer; the memory card or printer may be damaged. • To avoid loss of data, make a backup copy of the contents of the memory card. We cannot compensate for any damage to or loss of data. • Check the memory card and insert it in the correct direction. If a memory card is forcibly inserted in the wrong direction, the memory card and its slot may be damaged. • Check the memory card type and make sure to insert it to the slot designed for the particular card type. If you insert a memory card to a different slot, the memory card may be damaged or you may not be able to remove the memory card from the slot.  Viewing a slideshow.  Page 25 on the Operating Instructions  Copying or deleting an image  Page 27 on the Operating Instructions  Changing the print settings (Date print/border/borderless print)  Page 30 on the Operating Instructions  Changing the display/printer settings  Page 33 on the Operating Instructions You can connect the printer to other device.  Printing from a PictBridge-compliant camera  Page 35 on the Operating Instructions  Printing from a Bluetooth-compliant device.  Page 36 on the Operating Instructions  Printing from a mass-storage-compliant camera, USB memory or other device.  Page 38 on the Operating Instructions  Printing from a PC  Page 39 on the Operating Instructions  To display the image list/to enlarge an image ( / ) Press the (zoom out) button to display the image list. Press button to move the cursor (orange frame) to the image you want to print. To print the selected image, press the PRINT button. To print multiple copies, display one-image preview and set print quantity. (A 16-split-image list will be displayed in DPP-FP90.) To display one-image preview again, press ENTER or (zoom in) button. Pressing (zoom in) button enlarges the image up to 5 times the original scale.  To display the image information (  ) Each time you press the ENTER button, the image information display switches as follows: Standard display No image data display Image data display  On cleaning If white lines are printed as illustrated, you need to clean the printer.  Page 68 on the Operating Instructions  To correct a failed photo automatically (  ) When you are going to print a photo with a problem such as backlit, out-of-focus, or red-eye phenomenon, you can press the AUTO TOUCH-UP button to correct those problems automatically. The corrections of the selected image starts and their results will be displayed. If a face is detected during correction, it is shown with a frame as correction progress. To check the original picture Press the AUTO TOUCH-UP button again. To print the corrected image Press the PRINT button after corrections. The corrected image will be printed.  Tip The corrected image is for printing. The original image data is not corrected.  To save a corrected image 1 Display the image to which you want to add correction. 2 Press the MENU button. 3 Press / button to select (Edit) and then press the ENTER button. 4 Press the AUTO TOUCH-UP button. 5 Check that the corrections finishes for the image , and press / button to select (Save) and then press the ENTER button. For the details on saving, please refer to page 17 of the operating instructions.