Sony DVP-NW50 Installer Manual - Page 1
Sony DVP-NW50 - In-wall Dvd Player Manual
View all Sony DVP-NW50 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
2-584-980-11(2) Note Do not connect a VCR, etc., between your TV and the player. If you pass the player signals via the VCR, you may not receive a clear image on the TV screen. If your TV has only one video input jack, connect the Unit to this jack. Custom Integrated AV System Connecting audio Equipment Connections between the Unit and each of devices are made via cables or cords coming through the wall. The Unit can input sound from external audio equipment via the audio connectors on the Unit. Connect the OUTPUT jacks (L/R) of the audio equipment to the LINE IN (L/R) jacks of the Unit using the proper audio cords (optional). Tip Run the cables into the hole marked with an "*" in the illustration above, so that you can bundle and fix the cables. Notes • Make sure that the pre-construction bracket is properly level, both horizontally and vertically. Improper positioning may cause the unit to fall, or may cause difficulty when you install the Unit. • Make sure that more than 4 inches (10 cm) of space is available behind the wall for installing the unit. 3 Place the AM loop antenna on the stud, and then fasten the supplied screws to attach it. Raise the entire AM antenna, and then insert its tab into the notch to set up the AM loop antenna. Take care to attach the AM loop antenna on the stud as far away from the CDP-NW10, DVP-NW50, or other electrical devices as possible (at least 1 foot (30 cm)). Installer's manual This manual is for installers only. Contact your nearest installer for details on making the required connections for the system network. © 2005 Sony Corporation Printed in Korea Precautions Caution Unauthorized substitutions may result in fire, electric shock, causing die or serious injury. Keep the following precautions in mind to prevent any accidents. • Installment and settings other than that of specified instructions may cause the unit to fall due to lack of strength of the wall. • Do not use screws other than the supplied screws for installation. • Do not install the unit following any procedure other than that explained in this manual. Make sure to follow the procedure in this manual closely. • Do not disassemble the unit. This may cause a malfunction of the unit or cause injury to you. • Do not apply strong pressure on the unit after mounting it. The unit may be damaged or fall, causing a injury to you. On power sources • The Unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if the player itself has been turned off. • If you are not going to use the Unit for a long time, be sure to disconnect the Unit from the wall outlet. To disconnect the AC power cord, grasp the plug itself; never pull the cord. On placement • The Unit is designed for mounting only on the wall. You cannot mount it on the ceiling or on the floor. • Place the Unit in a location with adequate ventilation to prevent heat build-up in the Unit. • Do not place the Unit on a soft surface such as a rug. • Do not place the Unit in a location near heat sources, or in a place subject to direct sunlight, excessive dust, or mechanical shock. • Do not install the Unit in an inclined position. It is designed to be operated in a horizontal position only. • Keep the Unit and the discs away from equipment with strong magnets, such as microwave ovens, or large loudspeakers. • Do not install the unit in a humid location, such as in a bathroom, or a place where moisture condensation may occur. Install the Unit in a place where the environment falls within the operating temperature 0˚C - 40˚C (32˚F - 104˚F). • Do not step on or place heavy objects on the unit. The unit may be damaged or fall, causing injury to you. Unpacking Item CDP-NW10 CDP-NW10 Unit 1 DVP-NW50 Unit - Remote commander (remote) 1 (RM-ANU001 ) Wall mounting bracket 1 Wall stopper 4 TEMPLATE 1 Plug-in 4P terminal (for speakers) 1 Plug-in 5P terminal 1 (for AC power unit) Plug-in 6P terminal - (for AC power unit) Screws for fixing the Unit to 4 the wall mounting bracket (short) Screws for wall stopper (long) 4 AM loop antenna (aerial) 1 R6 (size-AA) battery 2 User's manual 1 Installer's manual (this manual) 1 DVP-NW50 - 1 1 1 4 1 3 - 1 4 4 1 2 1 1 CDP-NW10/DVP-NW50 System Network The diagram below illustrates an entire system network made up with multiple Units. Note The configuration shown below is for illustrative purpose only. It differs from an actual system network. KITCHEN BEDROOM GUEST ROOM CDP-NW10 CDP-NW10 CDP-NW10 INTERNET Router LIVING ROOM Front Speaker Hub DVP-NW50 Computer Front Speaker TV/Projector CD Changer Rear Speaker Center Speaker Sub Woofer Rear Speaker Example of the DVP-NW50 system network Connecting a computer Connect each Unit and a computer using an Ethernet cable (100Base-TX, optional.) For details on the connection, refer to "Hooking up the sysytem" on this manual and the instruction manual supplied with your router or hub. Connecting a TV (DVP-NW50 only) Connections between the Unit and each of devices are made via cables or cords coming through the wall. Connect the Unit to a TV or a projector using the VIDEO cord. Select one of the ways of connection methods shown below, according to the input jack on your TV. Connecting an IR IN/OUT Connections between the Unit and each of devices are made via cables or cords coming through the wall. You can operate a component using the remote if the IR IN/OUT terminal of the Unit and the component are connected. For example, if you connect IR IN of the Unit and IR OUT of a TV, you can operate the Unit with the remote by aiming it at the TV. If you connect IR OUT of the Unit and IR IN of a component, such as a DVD Changer, you can operate the DVD Changer with the remote (supplied with the DVD Changer) by aiming it at the Unit. Connecting an AC power unit After connecting the Unit and the AC power unit using the power supply cables, connect the AC power cord to the AC IN of the AC power unit, then the other end of the AC power cord to the wall outlet. Installing the Unit Before installing the Unit into the wall, take steps to ensure your safety and that of your surroundings, then check the following: • The location of the power source to make sure that power supply cable can reach from the Unit. • The location of the speakers to make sure that speaker cords can be run between the Unit and the speakers. • The distance between the Unit and the AC power unit (up to 200 feet (60 m)). • The durability of the wall (The thickness of the wall must be between 1/2 to 3/4 inches. (13 mm to 19 mm)). • There are no obstructions, such as an air, an electrical, or a water conduit near the location where the Unit is installed. • There is enough space (over 6 inches (15 cm)) inside the wall. If the space available inside the wall is insufficient or does not have proper ventilation, a malfunction of the Unit may occur due to heat build-up. • Do not install the Unit where the Unit may get wet due to water or other liquid. This may cause a malfunction of the Unit. • Do not install the Unit in a place where moisture condensation may cause a malfunction of the Unit. Installing brackets for new construction (before wall construction is finished) You may install a pre-construction bracket on the studs where the unit will be installed. It is recommended that you use a preconstruction bracket when you install the unit in a house that is still under construction. However, the pre-construction bracket is only for the use of sub installation. You may not be able to use the pre-construction bracket on the place where the wall and material of the wall and pillar may be damaged or some other problems may occur. Note The following items are included in the Pre-construction bracket kit (WSBKT1). • Pre-construction bracket (1) • Wings (2) • AM Antenna (1) • Screws for the AM Antenna (2) • Manual (1) 1 Insert the two wings into the tabs of the pre-construction bracket. Wing 2 Place the pre-construction bracket on the studs, and then fasten the screws (not supplied) to attach the preconstruction bracket. 4 After the wall construction is finished, cut the outline along the inside edge of the pre-construction bracket. Do not cut over or beyond the edge. Before proceeding to step 4, make sure that all the necessary cables can be run to the bracket location. Note Make sure that the size of the hole cut in the wall corresponds to the specified size (height: 83/8 X 87/16 inches, 212.5 - 215 mm), (width: 83/16 X 81/4 inches, 207.5 - 210 mm). If the hole is too big to mount the bracket, the Unit may fall and cause an accident. 5 Place the mounting bracket over the hole so that the pre- construction bracket and the mounting bracket match across the wall. Then fasten the wall mounting bracket screws carefully to fix the mounting bracket and preconstruction bracket so that they are level and align perfectly. Make sure the larger tab is mounted at the bottom. Larger tab Notes • Fasten the screws securely. Failure to fasten the screws or incomplete tightening of the screws may cause the Unit to fall and cause an accident. • For mounting the bracket, use the supplied screws. To mount the unit on the finished wall 1 Mark the location where the Unit is to be installed on the wall using the supplied TEMPLATE (83/8 X 81/4 inches (212.5 mm X 207.5 mm)). Make sure the mark is properly level, horizontally and vertically. 2 Cut the outline along the mark, then carefully cut a clean hole through the wall. Notes • Do not cut over or beyond the outline. • Make sure that the size if the hole cut in the wall corresponds to the specified size. If the hole is too big to mount the bracket, the Unit may fall and cause an accident. • Do not make a gap between the wall and the mounting bracket. 3 Rotate the stoppers to the inside of the frame, and then place the mounting bracket over the hole. Make sure the larger tab is mounted at the bottom. 4 Rotate the stoppers to the outside of the frame behind the wall. Larger tab 5 Fasten the wall mounting bracket screws carefully so that the wall mounting bracket is level. Notes • Fasten the screws securely. Failure to fasten the screws or incomplete tightening of the screws may cause the Unit to fall and cause an accident. * • For mounting the bracket, use the supplied screws.