Sony HCD-C770 Operating Instructions - Page 24

Setup for the system for Asian and Australian models, Connecting the AC Power Cord mains lead - dav

Get Sony HCD-C770 - Hi Fi Components PDF manuals and user guides View all Sony HCD-C770 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

FRONT R CENTER REAR R SPEAKER FRONT L WOOFER IMPEDANCE USE R E A R WOOFER 3Ω L EXCEPT WOOFER 3Ω AM COAXIAL FM 75Ω VIDEO 1 AUDIO OUT R L VIDEO OUT R L AUDIO IN VIDEO IN COMPONENT SCAN SELECT VIDEO OUT MONITOR OUT VIDEO 2 VIDEO S VIDEO AUDIO IN VIDEO IN SELECTABLE R L INTERLACE DVD ONLY OPTICAL DIGITAL IN Y PB/CB PR/CR COMPONENT VIDEO OUT VIDEO 2 IN OUT VIDEO VIDEO IN OUT AUDIO AUDIO IN OUT L R OUT OUT IN VIDEO OUT INPUT VIDEO IN AUDIO OUT L OUTPUT R OPTICAL VCR Digital satellite receiver TV monitor If you connect a digital satellite receiver with the OPTICAL jack The digital satellite receiver can be connected to the OPTICAL jack instead of the VIDEO IN and AUDIO IN L/R jacks of the system. The system can accept both the digital and analog signals. Digital signals have priority over analog signals. If the digital signal ceases, the analog signal will be processed after 2 seconds. If you connect a digital satellite receiver without the OPTICAL jack Connect the digital satellite receiver to the VIDEO IN and AUDIO IN L/R jacks only of the system. Setup for the system (for Asian and Australian models) Setup is necessary for the system, depending on the TV monitor to be connected. The initial setting for Asian models is NTSC but Australian models is PAL. If the color system of the TV is PAL* To set the system to PAL, turn on the system by pressing 1 (power) on the remote while pressing X (pause) button on the system. You need to hold the X button until DAV-C770 appears on the display. To reset to NTSC, turn off the system and then turn on again using the remote while pressing the X button on the system. * If the color system of the TV is NTSC, do the same operation above to set the system to NTSC. Connecting the AC Power Cord (mains lead) Before connecting the AC power cord (mains lead) of this system to a wall outlet (mains), connect the speakers to the system (see page 19). Connect the AC power cord (mains lead) of your TV/video components to a wall outlet (mains). 24GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
24
GB
WOOFER 3
Ω
IMPEDANCE
USE
EXCEPT
WOOFER 3
Ω
VIDEO 1
COMPONENT VIDEO OUT
VIDEO 2
VIDEO 2
MONITOR
OUT
FRONT
R
FRONT
L
REAR
R
REAR
L
CENTER
WOOFER
COAXIAL
AUDIO OUT
AUDIO IN
L
R
L
R
L
R
VIDEO OUT
VIDEO IN
VIDEO IN
AUDIO IN
Y
P
B
/C
B
P
R
/C
R
AM
FM
75
Ω
OPTICAL
DIGITAL
IN
S
VIDEO
VIDEO
DVD
ONLY
SPEAKER
INTERLACE
SELECTABLE
SCAN SELECT
COMPONENT
VIDEO OUT
IN
IN
OUT
OUT
OUT
VIDEO
OUT
R
VIDEO
IN
AUDIO
OUT
AUDIO
IN
L
VIDEO
OUT
R
AUDIO
OUT
L
OUTPUT
VIDEO
IN
INPUT
OPTICAL
If you connect a digital satellite receiver with the OPTICAL jack
The digital satellite receiver can be connected to the OPTICAL jack instead of the VIDEO IN
and AUDIO IN L/R jacks of the system.
The system can accept both the digital and analog signals. Digital signals have priority over
analog signals. If the digital signal ceases, the analog signal will be processed after 2 seconds.
If you connect a digital satellite receiver without the OPTICAL jack
Connect the digital satellite receiver to the VIDEO IN and AUDIO IN L/R jacks only of the
system.
Setup for the system (for Asian and Australian models)
Setup is necessary for the system, depending on the TV monitor to be connected.
The initial setting for Asian models is NTSC but Australian models is PAL.
If the color system of the TV is PAL
*
To set the system to PAL, turn on the system by pressing
1
(power) on the remote while
pressing
X
(pause) button on the system. You need to hold the
X
button until DAV-C770
appears on the display. To reset to NTSC, turn off the system and then turn on again using the
remote while pressing the
X
button on the system.
*If the color system of the TV is NTSC, do the same operation above to set the system to
NTSC.
Connecting the AC Power Cord (mains lead)
Before connecting the AC power cord (mains lead) of this system to a wall outlet (mains),
connect the speakers to the system (see page 19).
Connect the AC power cord (mains lead) of your TV/video components to a wall outlet (mains).
VCR
Digital satellite receiver
TV monitor