Sony HCD-HDX267W Operating Instructions - Page 69

AUDIO IN / A.CAL MIC, Press, to select [YES], then press, to select [YES] or [NO]

Get Sony HCD-HDX267W - Dvd/receiver Component For Home Theater System PDF manuals and user guides View all Sony HCD-HDX267W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

Advanced Settings and Adjustments Connect the calibration mic to the A.CAL MIC jack on the front panel, and set it up at the ear level using a tripod, etc. (not supplied). The front of each speaker should face the calibration mic, and there should be no obstruction between the speakers and the calibration mic. Be quiet during the measurement. AUDIO IN / A.CAL MIC Calibration mic Note • Avoid being in the measurement area and making noise during the measurement (about three minutes), to avoid measurement failure. During the measurement, test signals are output from the speakers. • The environment of the room in which the system is installed may affect measurements. • If an error message appears, follow the message, then select [YES]. An error message appears when: - the headphones are connected. - the calibration mic is not connected. - front speakers are not correctly connected. - surround speakers are not correctly connected. - front and surround speakers are not correctly connected. - there is excessive noise around the calibration mic. - the calibration mic is overloaded. 6 Press C/X/x/c to select [YES] or [NO], then press . x The measurement is OK. Disconnect the calibration mic, then select [YES]. The result is implemented. Measurement complete. FRONT L : YES FRONT R : YES CENTER : NONE SUBWOOFER : YES SURROUND L : NONE SURROUND R : NONE If OK, unplug calibration mic and select "YES". YES NO 5 Press X/x to select [YES], then press . Calibration starts. Measuring. Please wait a moment. x The measurement is not OK. Follow the message, then select [YES] to retry. Measurement failure. Check speaker connection. Retry? YES NO Tip • You can check the distance between the listening position and each speaker. See page 76. continued 69GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Advanced Settings and Adjustments
69
GB
Connect the calibration mic to the A.CAL
MIC jack on the front panel, and set it up at
the ear level using a tripod, etc. (not
supplied). The front of each speaker should
face the calibration mic, and there should be
no obstruction between the speakers and the
calibration mic. Be quiet during the
measurement.
5
Press
X
/
x
to select [YES], then press
Calibration starts.
Note
• Avoid being in the measurement area and
making noise during the measurement (about
three minutes), to avoid measurement failure.
During the measurement, test signals are output
from the speakers.
• The environment of the room in which the
system is installed may affect measurements.
• If an error message appears, follow the message,
then select [YES].
An error message appears when:
–
the headphones are connected.
–
the calibration mic is not connected.
–
front speakers are not correctly connected.
–
surround speakers are not correctly
connected.
–
front and surround speakers are not correctly
connected.
–
there is excessive noise around the
calibration mic.
–
the calibration mic is overloaded.
6
Press
C
/
X
/
x
/
c
to select [YES] or [NO],
then press
.
x
The measurement is OK.
Disconnect the calibration mic, then select
[YES]. The result is implemented.
x
The measurement is not OK.
Follow the message, then select [YES] to
retry.
Tip
• You can check the distance between the listening
position and each speaker. See page 76.
AUDIO IN / A.CAL MIC
Calibration mic
Measuring. Please wait a moment.
FRONT L :
FRONT R :
CENTER
:
SUBWOOFER :
SURROUND L :
SURROUND R :
If OK, unplug calibration mic and select
“YES”.
YES
YES
YES
NONE
YES
NONE
NONE
Measurement complete.
NO
Check speaker connection.
Retry?
YES
Measurement failure.
NO
continued