Sony HCD-U1BT Operating Instructions - Page 23

Continued, Tuner, To change the AM tuning interval, To improve tuner reception

Get Sony HCD-U1BT - Receiver Component For Micro Hi-fi Systems PDF manuals and user guides View all Sony HCD-U1BT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Files cannot be played back. • USB storage media formatted with file systems other than FAT16 or FAT32 are unsupported.* • If you use partitioned USB storage media, only files on the first valid partition can be played. • Files that are encrypted or protected by passwords, etc. cannot be played back. * This system supports FAT16 and FAT32, but some USB storage media may not support all of these FAT. For details, see the operation manual of each USB storage media or contact the manufacturer. Tuner Severe hum or noise, or stations cannot be received. ("TUNED" or "STEREO" flashes on the display.) • Connect the antenna properly. • Find a location and an orientation that provide good reception, and then set up the antenna again. • Keep the antennas away from the speaker cords, the power cord and the USB cable to avoid picking up noise. • Connect a commercially available external antenna. • Consult your nearest Sony dealer if the supplied AM antenna has come off the plastic stand. • Turn off nearby electrical equipment. To change the AM tuning interval The AM tuning interval is factory-preset to 9 kHz (or 10 kHz, for some areas; this function is not available on the European model). You cannot change the AM tuning interval in Power Saving Mode. Use buttons on the unit to change the AM tuning interval. 1 Tune in any AM station, and then turn off the system. 2 While holding down TUNER/BAND , press All the AM preset stations are erased. To reset the interval to the factory preset, repeat the procedure. To improve tuner reception Turn off CD player power by using the CD power management function. By default, CD power is turned on. You cannot change the setting in Power Saving Mode. Use buttons on the unit to turn off CD player power. 1 Press FUNCTION  repeatedly to select the CD function, and then turn off the system. 2 After "STANDBY" stops flashing, press /  while holding down  . "CD POWER OFF" appears. With CD player power turned off, disc access time is increased. To turn on CD player power, repeat the procedure until "CD POWER ON" appears. Others  Continued 23GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
±²
GB
Others
Files cannot be played back.
• USB storage media formatted with file
systems other than FAT16 or FAT32 are
unsupported.*
• If you use partitioned USB storage media,
only files on the first valid partition can be
played.
• Files that are encrypted or protected by
passwords, etc. cannot be played back.
*
°is system supports FAT16 and FAT32, but some USB
storage media may not support all of these FAT. For
details, see the operation manual of each USB storage
media or contact the manufacturer.
Tuner
Severe hum or noise, or stations cannot be
received. (“TUNED” or “STEREO” flashes on
the display.)
• Connect the antenna properly.
• Find a location and an orientation that
provide good reception, and then set up the
antenna again.
• Keep the antennas away from the speaker
cords, the power cord and the USB cable to
avoid picking up noise.
• Connect a commercially available external
antenna.
• Consult your nearest Sony dealer if the
supplied AM antenna has come off the plastic
stand.
• Turn off nearby electrical equipment.
To change the AM tuning interval
°e AM tuning interval is factory-preset to 9
kHz (or 10 kHz, for some areas; this function
is not available on the European model). You
cannot change the AM tuning interval in Power
Saving Mode.
Use buttons on the unit to change the AM
tuning interval.
1
Tune in any AM station, and then turn off
the system.
2
While holding down TUNER/BAND
,
press
/
.
All the AM preset stations are erased. To
reset the interval to the factory preset, repeat
the procedure.
To improve tuner reception
Turn off CD player power by using the CD
power management function. By default, CD
power is turned on. You cannot change the
setting in Power Saving Mode.
Use buttons on the unit to turn off CD player
power.
1
Press FUNCTION
repeatedly to select
the CD function, and then turn off the
system.
2
After “STANDBY” stops flashing, press
/
while holding down
.
“CD POWER OFF” appears. With CD
player power turned off, disc access time
is increased. To turn on CD player power,
repeat the procedure until “CD POWER
ON” appears.
Continued