Sony KDL-60W610B Operating Instructions (Setup Guide) (Large File - 12.18 MB) - Page 11

: Connecting the TV, Detaching the Table-Top, Stand from the TV - picture settings

Get Sony KDL-60W610B PDF manuals and user guides View all Sony KDL-60W610B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

2 Fix the TV to the Table-Top Stand using the supplied screws. The arrow marks indicate the location of the screw holes used for securing the Table-Top Stand. x 2 ~ • If using an electric screwdriver, set the torque at approximately 1.5 N·m {15 kgf·cm}. 2: Connecting the TV ~ • Use an antenna cable connector no greater than 14 mm thick. • When connecting the cable to the Cable/ Antenna, input finger tighten only, over tightening the connection can damage the US TV. • Before moving the TV, disconnect all of the cables connected to the TV to prevent damaging the TV when it is moved. • Use an HDMI cable connector within 12 mm (thickness) × 21 mm (width). • For more information on connections, refer to the i-Manual. x Shown with a Set Top Box with HDMI connection Detaching the Table-Top Stand from the TV To detach the Table-Top Stand from the TV, remove the screws fixed in step 2. ~ • Do not remove the Table-Top Stand for any reason other than to install corresponding accessories on the TV. • Be sure the TV is vertical before turning on. To avoid uneven picture uniformity do not power on the TV with the LCD panel facing down. • When attaching the Table-Top Stand again, be sure to fasten the screws (previously removed) to the original holes on the rear of the TV. Set Top Box (Continued) 11 US

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
11
US
US
2
Fix the TV to the Table-Top Stand using
the supplied screws. The arrow marks
indicate the location of the screw
holes used for securing the Table-Top
Stand.
~
•
If using an electric screwdriver, set the
torque at approximately 1.5 N·m
{15 kgf·cm}.
To detach the Table-Top Stand from the TV,
remove the screws fixed in step 2.
~
•
Do not remove the Table-Top Stand for any
reason other than to install corresponding
accessories on the TV.
•
Be sure the TV is vertical before turning on.
To avoid uneven picture uniformity do not
power on the TV with the LCD panel facing
down.
•
When attaching the Table-Top Stand again,
be sure to fasten the screws (previously
removed) to the original holes on the rear of
the TV.
2: Connecting the TV
~
•
Use an antenna cable connector no greater
than 14 mm thick.
•
When connecting the cable to the Cable/
Antenna, input finger tighten only, over
tightening the connection can damage the
TV.
•
Before moving the TV, disconnect all of the
cables connected to the TV to prevent
damaging the TV when it is moved.
•
Use an HDMI cable connector within 12 mm
(thickness) × 21 mm (width).
•
For more information on connections, refer to
the i-Manual.
x
Shown with a Set Top Box with
HDMI connection
Detaching the Table-Top
Stand from the TV
x 2
Set Top Box
(Continued)