Sony LSPX-102E26 Startup Guide - Page 2
Setting up the Speaker, Add function, Performing the Speaker, Add function stereo, mode/double mode - wireless light bulb speaker ()
View all Sony LSPX-102E26 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
Canceling the master unit setting Perform the steps listed in "Setting up the master unit" again. Note When canceling the master unit setting, perform the operation on only the master unit. If another bulb speaker (satellite unit) reacts, it may accidentally be set as a master unit. If another bulb speaker is nearby, turn off the light fixture to which it is installed. If multiple bulb speakers turn on when a light fixture is in use, remove the additional bulb speakers. Setting up the Speaker Add function 1 With the bulb speaker on the left side (master unit) already lit, turn on the light fixture to which the bulb speaker on the right side is installed. The bulb speaker lights up. L R Hint If you removed the bulb speaker on the right side when performing step 1 of "Setting up the master unit," reinstall the bulb speaker. 2 Aim the remote control toward the bulb speakers, then hold down the Volume + button for approximately one second after pressing and holding the STEREO/DOUBLE (switch mode)/ SHIFT (shift) button. L R Performing the Speaker Add function (stereo mode/double mode) 1 With both bulb speakers lit up, pair your BLUETOOTH device with the bulb speaker on the left side (master unit). For details see, "Pairing and Connecting with a BLUETOOTH Device." If pairing with the BLUETOOTH device has already been performed, then just connect. L R 2 Play music. The first time that you use the Speaker Add function after purchase, playback will be in stereo mode. Switching between stereo mode and double mode Aim the remote control toward the bulb speaker on the left side (master unit), and press the STEREO/ DOUBLE (switch mode)/SHIFT (shift) button. L R Canceling the Speaker Add function Aim the remote control toward the bulb speakers, then hold down the Volume - button for approximately one second after pressing and holding the STEREO/DOUBLE (switch mode)/SHIFT (shift) button. L R When the Speaker Add function has been canceled, music is played back normally from the bulb speaker on the left side, and is not played from the right side. Hint If there is distance between the bulb speakers, do this operation for the bulb speaker on the left side (master unit) first. Note The two bulb speakers will synchronize. To adjust the volume or brightness of the bulb speakers, aim the remote control toward the bulb speaker on the left side and then operate the remote control. If you want to use the bulb speaker on the right side independently, cancel the Speaker Add function. Adjusting the Brightness 1 Press the WHITE/COLOR (white/ color)/ OFF (light off) button to turn on the light. Each time you press the button the light switches between white light, color mode, and off. 2 Spin the dimmer/color ring to adjust the brightness. Spin to the right () for brighter, and spin to the left () for darker. When the light reaches its brightest setting, the main unit emits two short beeps. Note If you hold down the WHITE/COLOR (white/color)/ OFF (light off) button to turn off the light, BLUETOOTH will disconnect. When this happens, music cannot be played. To reconnect, press the WHITE/COLOR (white/color)/ OFF (light off) button again and turn on the light. Adjusting the Color 1 Press the WHITE/COLOR (white/ color)/ OFF (light off) button to switch the light to color mode. Each time you press the button, the light switches between white light, color mode, and off. 2 Spin the dimmer/color ring to adjust the color. Hint You can change the duration of the Sleep Timer from the LED Bulb Speaker Application. Canceling the Sleep Timer If you perform the step listed above once more, the Sleep Timer setting will be canceled. The bulb speaker will emit a long beep. Troubleshooting When the light flashes red at regular intervals The main unit has entered protection mode. When in protection mode, the remote control cannot be used to operate the unit. Turn off the light fixture to which the main unit is installed, and then turn it back on. Performing a factory reset Performing a factory reset can relieve some issues, but be aware that the following information will all be erased. --Pairing information --Brightness/color setting --Volume setting --Speaker Add function and master unit settings --Codec setting --EQ setting To perform a factory reset, follow the steps below. P ress and hold the WHITE/COLOR (white/color)/ OFF (light off) button on the remote control for five seconds to turn off the light. The unit will make a sound to indicate that BLUETOOTH has been disconnected. Release the button when you hear the sound. Press and hold the WHITE/COLOR (white/color)/ OFF (light off) button for five seconds. The main unit will blink several times in red, and then remain on at maximum brightness. There is noise when connected via BLUETOOTH. Depending on the surrounding environment, interfering signals can cause noise to be emitted from the main unit. In this case, change the location of the main unit. If the noise disappears depending on the location, the unit has not malfunctioned. The sound breaks up when using the Speaker Add function for playback Changing the playback quality (BLUETOOTH codec) setting for BLUETOOTH audio streaming on the main device to [SBC (Low)] may improve the issue. For details on how to switch the BLUETOOTH codec, refer to the Help Guide (online instruction manual). Refer to "Troubleshooting" in the Help Guide for more easy-to-understand troubleshooting tips. Use a computer or smartphone to access it. URL: http://rd1.sony.net/help/ speaker/lspx-102e26/h_zz/ Usable features of SongPal and LED Bulb Speaker Application for your smartphone/iPhone SongPal is an application that allows you to operate any supported Sony audio devices from your smartphone/iPhone. The LED Bulb Speaker Application is an enhancement app for SongPal that allows you to operate the light settings for this product. ÔÔPlease be aware that the availability of these functions depends on your version of SongPal. For details, see the Help Guide. http://rd1.sony.net/help/speaker/lspx-102e26/h_zz/ How to Download Search for SongPal in Google Play™ (Play Store) or the App Store, and download. Then, when you select LED Bulb Speaker Application from the settings screen of SongPal, Google Play (Play Store) or the App Store will open, and you can download the enhancement app. Select LED Bulb Speaker Application. The bulb speaker on the left side will emit a series of short beeps, while the speaker on the right will emit a series of long beeps. Hints • If there is distance between the bulb speakers, perform step 2 for one speaker at a time. • The Speaker Add function cannot be set for several seconds after the light fixture is turned on. Please wait a moment before performing step 2. Confirming which is the master unit (left channel)/satellite unit (right channel) When the main unit is connected to a BLUETOOTH device, aim the remote control toward the two bulb speakers, and press the WHITE/COLOR (white/ color)/ OFF (light off) button. The master unit (left channel) will react slightly sooner than the other bulb speaker. Using the Sleep Timer 1 Press the WHITE/COLOR (white/ color)/ OFF (light off) button while pressing the STEREO/DOUBLE (switch mode)/SHIFT (shift) button. The bulb speaker emits a short beep. The Sleep Timer is set, and the light will automatically turn off after 60 minutes (duration setting at time of purchase). If music is playing, it will pause. To reconnect to a BLUETOOTH device after performing a reset, delete the pairing information for the main unit from your BLUETOOTH device, and then follow the steps listed in "Pairing and connecting with a BLUETOOTH device" again. FAQ Sound from specific smartphone apps doesn't play. When connected with a smartphone, sound from some specific applications may not be output from the main unit, but the unit has not malfunctioned. There is a possibility that audio data is not being released wirelessly from the smartphone. For more information, refer to the instruction manual for your smartphone. SongPal features • Adjust the volume • Set the sound quality LED Bulb Speaker Application features • Switch the light mode (off, white light, color) • Adjust the brightness (dimmer) • Set the color and color effect • Set the Sleep Timer • Set the Wake-Up Timer (only Android) ÔÔFor details, see the Help Guide. http://rd1.sony.net/help/speaker/ lspx-102e26/h_zz/