Sony MEX-DV1700U Installation/Connections - Page 1

4-296-932-11(1) Multi Disc Player Installation/Connections A VIDEO OUT FRONT AUDIO OUT Monitor (not supplied) REAR / SUB AUDIO OUT B Satellite radio tuner (SiriusXM)* SIRIUSXM IN * not supplied MEX-DV1707U/MEX-DV1700U    × 2   * * × 4 * except for U.S. models Equipment used in illustrations (not supplied) Front speaker Subwoofer Rear speaker Power amplifier *1 *1 Monitor (not supplied) REAR / SUB AUDIO OUT*2 *1 FRONT *3 AUDIO OUT AUX AUDIO IN VIDEO OUT SIRIUSXM IN*5 *1 RCA pin cord (not supplied) *2 AUDIO OUT can be switched SUB or REAR. For details, see the supplied Operating Instructions. *3 Auxiliary device such as hideaway navigation device, TV tuner box, etc. *4 Separate adaptor may be required. *5 U.S. models only. *6 For details on connecting to the parking brake switch cord, see "Connecting the parking brake cord ()" on the reverse side. Satellite radio tuner (SiriusXM)*5 Left Right Left Right from car antenna (aerial) Fuse (10 A) REM OUT Max. supply current 0.4 A Blue/white striped REMOTE IN*4  White White/black striped Gray Gray/black striped Green Green/black striped Purple Purple/black striped Black Orange/white striped Red Yellow Light green ILLUMINATION PARKING BRAKE *6 Cautions  This unit is designed for negative ground (earth) 12 V DC operation only.  Do not get the leads under a screw, or caught in moving parts (e.g. seat railing).  Before making connections, turn the car ignition off to avoid short circuits.  Connect the yellow and red power supply leads only after all other leads have been connected.  Run all ground (earth) leads to a common ground (earth) point.  Be sure to insulate any loose unconnected leads with electrical tape for safety.  The use of optical instruments with this product will increase eye hazard. Notes on the power supply lead (yellow)  When connecting this unit in combination with other stereo components, the connected car circuit's rating must be higher than the sum of each component's fuse.  When no car circuits are rated high enough, connect the unit directly to the battery. Parts Iist  The numbers in the list are keyed to those in the instructions.  The bracket  and the protection collar  are attached to the unit before shipping. Before mounting the unit, use the release keys  to remove the bracket  from the unit. For details, see "Removing the protection collar and the bracket ()" on the reverse side of the sheet.  Keep the release keys  for future use as they are also necessary if you remove the unit from your car. Caution Handle the bracket  carefully to avoid injuring your fingers.  Catch Note Before installing, make sure that the catches on both sides of the bracket  are bent inwards 2 mm (3/32 in). If the catches are straight or bent outwards, the unit will not be installed securely and may spring out. Connection example Notes (-A)  Be sure to connect the ground (earth) lead before connecting the amplifier.  The alarm will only sound if the built-in amplifier is used. Connection diagram  To a metal surface of the car First connect the black ground (earth) lead, then connect the yellow and red power supply leads.  To the power antenna (aerial) control lead or power supply lead of antenna (aerial) booster Notes  It is not necessary to connect this lead if there is no power antenna (aerial) or antenna (aerial) booster, or with a manually-operated telescopic antenna (aerial).  When your car has a built-in FM/AM antenna (aerial) in the rear/ side glass, see "Notes on the control and power supply leads." To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers. Connecting any other system may damage the unit.  To a car's illumination signal Be sure to connect the black ground (earth) lead to a metal surface of the car first.  To the +12 V power terminal which is energized in the accessory position of the ignition switch Notes  If there is no accessory position, connect to the +12 V power (battery) terminal which is energized at all times. Be sure to connect the black ground (earth) lead to a metal surface of the car first.  When your car has a built-in FM/AM antenna (aerial) in the rear/ side glass, see "Notes on the control and power supply leads."  To the +12 V power terminal which is energized at all times Be sure to connect the black ground (earth) lead to a metal surface of the car first.  To the parking brake switch cord Notes on the control and power supply leads  REM OUT lead (blue/white striped) supplies +12 V DC when you turn on the unit.  When your car has built-in FM/AM antenna (aerial) in the rear/side glass, connect REM OUT lead (blue/white striped) or the accessory power supply lead (red) to the power terminal of the existing antenna (aerial) booster. For details, consult your dealer.  A power antenna (aerial) without a relay box cannot be used with this unit. Memory hold connection When the yellow power supply lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off. Notes on speaker connection  Before connecting the speakers, turn the unit off.  Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to avoid its damage.  Do not connect the speaker terminals to the car chassis, or connect the terminals of the right speakers with those of the left speaker.  Do not connect the ground (earth) lead of this unit to the negative (-) terminal of the speaker.  Do not attempt to connect the speakers in parallel.  Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speaker terminals may damage the unit.  To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative (-) lead for the right and left speakers.  Do not connect the unit's speaker leads to each other. Notes on connection  If speaker and amplifier are not connected correctly, "FAILURE" appears in the display. In this case, make sure the speaker and amplifier are connected correctly.  If you are to use the monitor for the rear seats, connect the parking brake switch cord to the ground (earth).