Sony MHC-BX6AV Operating Instructions - Page 11

Press ENTER., Repeat steps 1 through 4 to store, other stations., To tune in a station with a weak

Get Sony MHC-BX6AV PDF manuals and user guides View all Sony MHC-BX6AV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

4 Press ENTER. The station is stored. 5 Repeat steps 1 through 4 to store other stations. To tune in a station with a weak signal Press + or - (or TUNING +/- on the remote) repeatedly in step 2 to tune in the station manually. To set another station to an existing preset number Start over from step 1. After step 3, turn the shuttle until it clicks to select the preset number where you want to store the other station. You can preset a new station in the selected preset number. To erase a preset station 1 Press and hold TUNER MEMORY until a preset number appears in the display. ALL DISCS VOLUME ß 2 Turn the shuttle until it clicks to select the preset number you want to erase. Select "ALL ERASE" when you want to erase all the preset stations. 3 Press ENTER. "COMPLETE" appears in the display. When you erase a preset number, the preset number decreases by one and all preset numbers following the erased one are renumbered. To change the AM tuning interval (Except for the European and Middle Eastern models) The AM tuning interval is factory-preset to 9 kHz (10 kHz in some areas). To switch the AM tuning interval, tune in any AM station first, then turn off the power. While holding down TUNER/BAND, turn the power back on. When you switch the interval, AM preset stations are erased. To switch back to the original interval, repeat the same procedure. Tip The preset stations are retained for half a day even if you unplug the power cord or a power failure occurs. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
11
VOLUME
ALL
DISCS
ß
4
Press ENTER.
The station is stored.
5
Repeat steps 1 through 4 to store
other stations.
To tune in a station with a weak
signal
Press + or – (or TUNING +/– on the remote)
repeatedly in step 2 to tune in the station
manually.
To set another station to an
existing preset number
Start over from step 1. After step 3, turn the
shuttle until it clicks to select the preset
number where you want to store the other
station.
You can preset a new station in the selected
preset number.
To erase a preset station
1
Press and hold TUNER MEMORY until a
preset number appears in the display.
2
Turn the shuttle until it clicks to select the
preset number you want to erase.
Select “ALL ERASE” when you want to
erase all the preset stations.
3
Press ENTER.
“COMPLETE” appears in the display.
When you erase a preset number, the preset
number decreases by one and all preset
numbers following the erased one are
renumbered.
To change the AM tuning interval
(Except for the European and Middle
Eastern models)
The AM tuning interval is factory-preset to 9 kHz
(10 kHz in some areas). To switch the AM tuning
interval, tune in any AM station first, then turn off
the power. While holding down TUNER/BAND,
turn the power back on. When you switch the
interval, AM preset stations are erased. To switch
back to the original interval, repeat the same
procedure.
Tip
The preset stations are retained for half a day even if
you unplug the power cord or a power failure
occurs.