Sony RM-AV3100 Operating Instructions - Page 17

Press CHANNEL + or CHANNEL, Press the ENTER key. - remote

Get Sony RM-AV3100 - Integrated Remote Commander PDF manuals and user guides
UPC - 027242643154
View all Sony RM-AV3100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

4 Press CHANNEL + or CHANNEL - to search component code numbers in the same category (in this case, code numbers which begin with "8"). Press CHANNEL + to go to the next code number. Press CHANNEL - to go back to the previous code number. CHANNEL Note To search component code numbers in another category, return to Step 3, or input a four-digit component code number of another category (for example, a code number which begins with "3," "4," etc.) before Step 4. 5 Aim the Commander at the component and press the POWER key. If it successfully works (power-off for TV, AMP, playback for CD, MD, DAT, TAPE, light-off for LIGHTING and power-on for other components), go to Step 6. If it does not, repeat Steps 4 to 5. 6 Press the ENTER key. A beep sounds, and the selected component name, the preset fourdigit component code number and "OK" light for two seconds. And the display returns to Step 2. Note It is recommended to write down the code number. 7 Press COMMANDER OFF. COMMANDER OFF If you keep COMMANDER OFF pressed for more than 2 seconds The Commander turns off. If you keep COMMANDER OFF pressed for less than 2 seconds The Commander returns to the previous set mode. When the remote control signal is sent, is shown on the display. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
17
4
Press CHANNEL + or CHANNEL –
to search component code numbers
in the same category (in this case,
code numbers which begin with “8”).
Press CHANNEL + to go to the next
code number.
Press CHANNEL – to go back to the
previous code number.
CHANNEL
Note
To search component code numbers in
another category, return to Step 3, or input
a four-digit component code number of
another category (for example, a code
number which begins with “3,” “4,” etc.)
before Step 4.
5
Aim the Commander at the
component and press the POWER
key.
When the remote control signal is
sent,
is shown on the display.
If it successfully works (power-off for
TV, AMP, playback for CD, MD, DAT,
TAPE, light-off for LIGHTING and
power-on for other components), go
to Step 6.
If it does not, repeat Steps 4 to 5.
6
Press the ENTER key.
A beep sounds, and the selected
component name, the preset four-
digit component code number and
“OK” light for two seconds. And the
display returns to Step 2.
Note
It is recommended to write down the code
number.
7
Press COMMANDER OFF.
COMMANDER
OFF
If you keep COMMANDER OFF
pressed for more than 2 seconds
The Commander turns off.
If you keep COMMANDER OFF
pressed for less than 2 seconds
The Commander returns to the previous set
mode.