Sony SRG-X400 BRC-X400 / X401 / SRG-X400 / X402 / 201M2 / X120 / HD1M2 CGI Com - Page 3

Overview, About This Document, Advance Preparation, HTTP/RTSP Communication Usage Setting

Get Sony SRG-X400 PDF manuals and user guides View all Sony SRG-X400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

Overview About This Document This document describes about CGI command specifications and RTSP streaming specifications of Sony color video camera BRC-X400 Series (BRC-X400, BRC-X401, SRG-X400, SRG-X402, SRG-201M2, SRG-X120, SRG-HD1M2). In this document, the product is referred as "the cameras" or "this device." Advance Preparation This document provides information about how to control this device remotely via network and stream video/audio by using CGI commands supported by this device and RTSP function. To use CGI commands and RTSP streaming function, some pre-configurations are required. These pre-configurations are described below. HTTP/RTSP Communication Usage Setting To use CGI commands and RTSP streaming function on this device, you need to set appropriate HTTP/RTSP communication usage to enable communication via network in advance. To do this, there are 2 methods:  Set CAMERA SETUP switch,  Set HTTP/RTSP on the OSD menu.  Set CAMERA SETUP switch Set CAMERA SETUP 3 (HTTP/RTSP communication use setting) switch on the back of the camera to ON. Turn off the power, then turn on again to start.  Set HTTP/RTSP on the OSD menu Connect HDMI OUT terminal or SDI OUT terminal to video monitor. Display SYSTEM menu using infrared remote. Change HTTP/ RTSP setting to ON. Turn off the power of the camera, then turn on again to start. When the CAMERA SETUP 3 (HTTP/RTSP communication use setting) switch is set to ON in , HTTP/RTSP communication is available regardless the setting of OSD menu. IP Address Settings by RM-IP Setup Tool To enable the device to communicate with the camera appropriately, IP address settings is required. Set IP address based on your network environment using RM-IP Setup Tool. This is in order to set IP address. For details, refer to "RMIP Setup Tool Guide." Note  IP address is set to 192.168.0.100 as default.  When IPSetupSetEnable (page 41) is set to off, the camera does not accept RM-IP Setup Tool setting. 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
3
Overview
About This Document
This document describes about CGI command
specifications and RTSP streaming specifications
of Sony color video camera BRC-X400 Series
(BRC-X400, BRC-X401, SRG-X400, SRG-X402,
SRG-201M2, SRG-X120, SRG-HD1M2).
In this document, the product is referred as “the
cameras” or “this device.”
Advance Preparation
This document provides information about how
to control this device remotely via network and
stream video/audio by using CGI commands
supported by this device and RTSP function.
To use CGI commands and RTSP streaming
function, some pre-configurations are required.
These pre-configurations are described below.
HTTP/RTSP Communication Usage
Setting
To use CGI commands and RTSP streaming
function on this device, you need to set
appropriate HTTP/RTSP communication usage
to enable communication via network in
advance. To do this, there are 2 methods:
Set CAMERA SETUP switch,
Set HTTP/RTSP
on the OSD menu.
Set CAMERA SETUP switch
Set CAMERA SETUP 3 (HTTP/RTSP
communication use setting) switch on the
back of the camera to ON. Turn off the
power, then turn on again to start.
Set HTTP/RTSP on the OSD menu
Connect HDMI OUT terminal or SDI OUT
terminal to video monitor. Display SYSTEM
menu using infrared remote. Change HTTP/
RTSP setting to ON. Turn off the power of the
camera, then turn on again to start.
When the CAMERA SETUP 3 (HTTP/RTSP
communication use setting) switch is set to
ON in
, HTTP/RTSP communication is
available regardless the setting of OSD
menu.
IP Address Settings by RM-IP
Setup Tool
To enable the device to communicate with the
camera appropriately, IP address settings is
required. Set IP address based on your network
environment using RM-IP Setup Tool. This is in
order to set IP address. For details, refer to “RM-
IP Setup Tool Guide.”
Note
IP address is set to 192.168.0.100 as default.
When IPSetupSetEnable (page 41) is set to off,
the camera does not accept RM-IP Setup Tool
setting.