Sony STR-DA5700ES Operating Instructions (Large File - 11.23 MB) - Page 48

Release the TONE MODE and, MODE and 2CH/A.DIRECT

Get Sony STR-DA5700ES PDF manuals and user guides View all Sony STR-DA5700ES manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Performing initial setup operations (clearing all memorized settings) Before using the receiver for the first time, initialize the receiver by performing the following procedure. This procedure can also be used to revert back to the factory default settings. ?/1 TONE MODE 2CH/A.DIRECT Inserting batteries into the remote control Insert two R6 (size-AA) batteries in the RM-AAL040 remote control, and the RM-AAU124 remote control. Observe the correct polarity when installing batteries. 1 Press ?/1 to turn off the receiver. 2 While holding down the TONE MODE and 2CH/A.DIRECT, press ?/1 to turn on the receiver. 3 Release the TONE MODE and 2CH/A.DIRECT after a few seconds. The "MEMORY CLEARING..." appears on the display window for a while, then changes to "MEMORY CLEARED!" Changes or adjustments made to the settings are now reset to the defaults. Note It takes about one minute for the memory to be cleared completely. Do not turn the receiver off until "MEMORY CLEARED!" appears on the display. RM-AAL040 RM-AAU124 Notes • Do not leave the remote control in an extremely hot or humid place. • Do not use a new battery with old ones. • Do not mix manganese batteries and other kinds of batteries. • If you do not intend to use the remote control for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion. • When you replace or remove the batteries, the programmed codes may be cleared. If this happens, program the remote control codes again (page 128, 132, 133). 48US

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
48
US
Before using the receiver for the first time,
initialize the receiver by performing the
following procedure. This procedure can also
be used to revert back to the factory default
settings.
1
Press
?
/
1
to turn off the
receiver.
2
While holding down the TONE
MODE and 2CH/A.DIRECT,
press
?
/
1
to turn on the
receiver.
3
Release the TONE MODE and
2CH/A.DIRECT after a few
seconds.
The “MEMORY CLEARING...” appears
on the display window for a while, then
changes to “MEMORY CLEARED!”
Changes or adjustments made to the
settings are now reset to the defaults.
Note
It takes about one minute for the memory to be
cleared completely. Do not turn the receiver off until
“MEMORY CLEARED!” appears on the display.
Insert two R6 (size-AA) batteries in the
RM-AAL040 remote control, and the
RM-AAU124 remote control.
Observe the correct polarity when installing
batteries.
Notes
• Do not leave the remote control in an extremely hot
or humid place.
• Do not use a new battery with old ones.
• Do not mix manganese batteries and other kinds of
batteries.
• If you do not intend to use the remote control for an
extended period of time, remove the batteries to
avoid possible damage from battery leakage and
corrosion.
• When you replace or remove the batteries, the
programmed codes may be cleared. If this happens,
program the remote control codes again (page 128,
132, 133).
Performing initial setup
operations (clearing all
memorized settings)
?
/
1
TONE MODE
2CH/A.DIRECT
Inserting batteries into the
remote control
RM-AAL040
RM-AAU124