Sony STR-K700 Operating Instructions - Page 54

Remote, control, Error, messages

Get Sony STR-K700 - Fm Stereo/fm-am Receiver PDF manuals and user guides View all Sony STR-K700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

The FM reception is poor. • Use a 75-ohm coaxial cable (not supplied) to connect the receiver to an outdoor FM antenna as shown below. If you connect the receiver to an outdoor antenna, ground it against lightning. To prevent a gas explosion, do not connect the ground wire to a gas pipe. Outdoor FM antenna Receiver Ground wire (not supplied) To ground Radio stations cannot be tuned in. • Check that the antennas are connected securely. Adjust the antennas and connect an external antenna, if necessary. • The signal strength of the stations is too weak (when tuning in with automatic tuning). Use direct tuning. • Make sure you set the tuning interval correctly (when tuning in AM stations with direct tuning). • No stations have been preset or the preset stations have been cleared (when tuning by scanning preset stations). Preset the stations (page 44). • Press DISPLAY repeatedly on the receiver so that the frequency appears on the display. There is no picture appears on the TV screen or monitor. • Make sure you have connected the video output of your video component to the TV. Remote control The remote does not function. • Point the remote at the remote sensor on the receiver. • Remove any obstacles in the path between the remote and the receiver. • Replace all the batteries in the remote with new ones, if they are weak. • Make sure you select the correct input on the remote. Error messages If there is a malfunction, the display shows a message. You can check the condition of the system by the message. Refer to the following table to solve the problem. If any problem persists, consult your nearest Sony dealer. If an error message appears while you perform Auto Calibration, see "Error and warning codes" (page 22) to solve the problem. DEC. EROR Appears when a signal the receiver cannot decode (ex. DTS-CD) is input and "DEC. PRI." on the AUDIO menu is set to "DEC. PCM". Set it to "DEC. AUTO" (page 30). PROTECT Irregular current is output from the speakers. The receiver will automatically turn off after a few seconds. Check the speaker connection and turn on the power again. 54US

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
The
FM
reception
is
poor.
•
Use
a
75
-ohm
coaxial
cable
(not
supplied)
to
connect
the
receiver
to
an
outdoor
FM
antenna
as
shown
below.
If
you
connect
the
receiver
to
an
outdoor
antenna,
ground
it
against
lightning.
To
prevent
a
gas
explosion,
do
not
connect
the
ground
wire
to
a
gas
pipe.
Outdoor
FM
antenna
Receiver
Ground
wire
(not
supplied)
To
ground
Radio
stations
cannot
be
tuned
in.
•
Check
that
the
antennas
are
connected
securely.
Adjust
the
antennas
and
connect
an
external
antenna,
if
necessary.
•
The
signal
strength
of
the
stations
is
too
weak
(when
tuning
in
with
automatic
tuning).
Use
direct
tuning.
•
Make
sure
you
set
the
tuning
interval
correctly
(when
tuning
in
AM
stations
with
direct
tuning).
•
No
stations
have
been
preset
or
the
preset
stations
have
been
cleared
(when
tuning
by
scanning
preset
stations).
Preset
the
stations
(page
44).
•
Press
DISPLAY
repeatedly
on
the
receiver
so
that
the
frequency
appears
on
the
display.
There
is
no
picture
appears
on
the
TV
screen
or
monitor.
•
Make
sure
you
have
connected
the
video
output
of
your
video
component
to
the
TV.
Remote
control
The
remote
does
not
function.
•
Point
the
remote
at
the
remote
sensor
on
the
receiver.
•
Remove
any
obstacles
in
the
path
between
the
remote
and
the
receiver.
•
Replace
all
the
batteries
in
the
remote
with
new
ones,
if
they
are
weak.
•
Make
sure
you
select
the
correct
input
on
the
remote.
Error
messages
If
there
is
a
malfunction,
the
display
shows
a
message.
You
can
check
the
condition
of
the
system
by
the
message.
Refer
to
the
following
table
to
solve
the
problem.
If
any
problem
persists,
consult
your
nearest
Sony
dealer.
If
an
error
message
appears
while
you
perform
Auto
Calibration,
see
"Error
and
warning
codes"
(page
22)
to
solve
the
problem.
DEC.
EROR
Appears
when
a
signal
the
receiver
cannot
decode
(ex.
DTS-CD)
is
input
and
"DEC.
PRI."
on
the
AUDIO
menu
is
set
to
"DEC.
PCM".
Set
it
to
"DEC.
AUTO"
(page
30).
PROTECT
Irregular
current
is
output
from
the
speakers.
The
receiver
will
automatically
turn
off
after
a
few
seconds.
Check
the
speaker
connection
and
turn
on
the power
again.
54US