Sony SVR-2000 TiVo Viewer"s Guide (primary manual) - Page 85

Cable/Satellite Box, then Control Cable Setup. Verify the IR code you chose during - remote codes

Get Sony SVR-2000 PDF manuals and user guides
UPC - 027242566026
View all Sony SVR-2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

Chapter 6 78 Troubleshooting I can't get the channel to change. (continued) If you use cable with a set-top box: • Make sure the set-top box is turned on. • Make sure you are using the recorder's remote control, and that you hold it so that the TiVo button points toward the recorder, not a cable or satellite box. • Refer to the Start Here booklet to verify that the IR Control cable is positioned correctly. • Press the TiVo button to go to TiVo Central, then select Messages & Setup, then Cable/Satellite Box, then Control Cable Setup. Verify the IR code you chose during Guided Setup. See page 7 for help choosing an IR code. • If the installation instructions required you to connect a serial control cable, check that the Serial Control cable is plugged into the upper serial jack on the back of the recorder. • Unplug the cable set-top box from the wall, then plug it back in. If you use a satellite receiver with an IR Control cable: • Make sure the satellite receiver is turned on. • Refer to the Start Here booklet to verify that the IR Control cable is positioned correctly. • Press the TiVo button to go to TiVo Central, then select Messages & Setup, then Cable/Satellite Box, then Control Cable Setup. Verify the IR code you chose during Guided Setup. See page 7 for help choosing an IR code. • Unplug the satellite set-top box from the wall, then plug it back in.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
78
Chapter 6
Troubleshooting
I can’t get the channel to change. (continued)
If you use cable with a set-top box:
•
Make sure the set-top box is turned on.
•
Make sure you are using the recorder’s remote control, and that you hold it so that the
TiVo button points toward the recorder, not a cable or satellite box.
•
Refer to the
Start Here
booklet to verify that the IR Control cable is positioned
correctly.
•
Press the TiVo button to go to TiVo Central, then select Messages & Setup, then
Cable/Satellite Box, then Control Cable Setup. Verify the IR code you chose during
Guided Setup. See page 7 for help choosing an IR code.
•
If the installation instructions required you to connect a serial control cable, check that
the Serial Control cable is plugged into the upper serial jack on the back of the
recorder.
•
Unplug the cable set-top box from the wall, then plug it back in.
If you use a satellite receiver with an IR Control cable:
•
Make sure the satellite receiver is turned on.
•
Refer to the
Start Here
booklet to verify that the IR Control cable is positioned
correctly.
•
Press the TiVo button to go to TiVo Central, then select Messages & Setup, then
Cable/Satellite Box, then Control Cable Setup. Verify the IR code you chose during
Guided Setup. See page 7 for help choosing an IR code.
•
Unplug the satellite set-top box from the wall, then plug it back in.