Sony VPL-VW890ES Operating Instructions - Page 33

Using Network Features, Displaying the Control Window of the Unit with a Web Browser

Get Sony VPL-VW890ES PDF manuals and user guides View all Sony VPL-VW890ES manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Using Network Features Connection to the network allows you to operate the following features. Use the projector with only necessary functions enabled. • Checking the current status of the unit via a Web browser. • Making the network settings for the unit. • Network monitoring and controlling with control protocol (Advertisement, ADCP, AMX DDDP (Dynamic Device Discovery Protocol), Crestron RoomView, Control4). Notes • When connecting this projector with the network, consult with the person who sets up the network. The network must be secured. • When using this projector connected with the network, access the Control window via a Web browser and change the access limitation of the factory preset values (page 34). It is recommended to change the password regularly. • When the setting on the Web browser is completed, close the Web browser to log out. • The menu displays used for the explanation below may be different depending on the model you are using. • Supported Web browsers are Internet Explorer (version 11 or later), Safari, and Chrome. • The menu displays only English. • If the browser of your computer is set to [Use a proxy server] when you have access to the unit from your computer, click the check mark to set accessing without using a proxy server. • AMX DDDP is not compatible with IPv6. • These network functions are available when the unit is turned on. 3 Start a Web browser on the computer, enter the following in the address field, then press the Enter key on your computer. http://xxx.xxx.xxx.xxx (xxx.xxx.xxx.xxx: IP address for the unit) When connecting by the IPv6 address http://[xxxx:xxxx:- xxxx] You can confirm the IP address of the unit under "Network Setting" on the Installation menu. The following window appears in the Web browser: Once you make the network settings, you can open the Control window only by performing step 3 of this procedure. Displaying the Control Window of the Unit with a Web Browser 1 Connect the LAN cable. LAN cable (straight type) (not supplied) LAN Connector Hub, router, etc. 2 Set the network settings for the unit using "Network Setting" on the Installation menu (page 31). 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
33
Connection to the network allows you to operate the
following features.
Use the projector with only necessary functions enabled.
•
Checking the current status of the unit via a Web
browser.
•
Making the network settings for the unit.
•
Network monitoring and controlling with control
protocol (Advertisement, ADCP, AMX DDDP
(Dynamic Device Discovery Protocol), Crestron
RoomView, Control4).
•
When connecting this projector with the network, consult with the
person who sets up the network. The network must be secured.
•
When using this projector connected with the network, access the
Control window via a Web browser and change the access
limitation of the factory preset values (page 34). It is
recommended to change the password regularly.
•
When the setting on the Web browser is completed, close the Web
browser to log out.
•
The menu displays used for the explanation below may be
different depending on the model you are using.
•
Supported Web browsers are Internet Explorer (version 11 or
later), Safari, and Chrome.
•
The menu displays only English.
•
If the browser of your computer is set to [Use a proxy server] when
you have access to the unit from your computer, click the check
mark to set accessing without using a proxy server.
•
AMX DDDP is not compatible with IPv6.
•
These network functions are available when the unit is turned on.
Displaying the Control
Window of the Unit with a
Web Browser
1
Connect the LAN cable.
2
Set the network settings for the unit using “Network
Setting” on the Installation
menu (page 31).
3
Start a Web browser on the computer, enter the
following in the address field, then press the Enter key
on your computer.
(xxx.xxx.xxx.xxx: IP address for the unit)
When connecting by the IPv6 address
http://[xxxx:xxxx:- xxxx]
You can confirm the IP address of the unit under
“Network Setting” on the Installation
menu.
The following window appears in the Web browser:
Once you make the network settings, you can open the
Control window only by performing step
3
of this
procedure.
Using Network Features
Notes
LAN
Connector
LAN cable
(straight type)
(not supplied)
Hub, router, etc.