Stihl AR 2000 Instruction Manual - Page 13

LED Diagnostics and Acoustic Signals

Get Stihl AR 2000 PDF manuals and user guides View all Stihl AR 2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

9 LED Diagnostics and Acoustic Signals AP Adapter. Never use a wet charger, @ 5.1. Follow all product-specific warnings and instructions accompanying your charger. To charge the battery: 3 12 4 5 3 English Charging time depends on a number of factors, including battery condition and the ambient temperature. For a complete list of approximate charging times, see www.stihl.com/charging-times. 9 LED Diagnostics and Acoustic Signals 9.1 Battery Status Six LEDs and an acoustic signal indicate the status of the battery. 1 0000-GXX-2680-A0 0000-GXX-3229-A1 ► Push the plug of the connecting cord (1) into the socket (2) of the AP Adapter (3) until it stops. ► Push the AP Adapter into the charger (5) until it stops. The LED on the charger (4) glows green when the battery is charging. The LEDs on the AR battery glow green and show the state of charge. When the LEDs on the battery turn off, the charging process is complete and the charger will shut itself off. ► Remove the AP Adapter from the charger and disconnect the charger's power supply cord from the electrical outlet when charging is complete. A battery is not fully charged when it ships from the factory. STIHL recommends that you fully charge the backpack battery before using it the first time. Operate the charger only indoors, in dry rooms and within an ambient temperature range of 41 °F to 104 °F (5 °C to 40 °C). The battery heats up during operation of the power tool. If a hot battery is connected to the charger, it may be necessary for it to cool down before charging starts. The charging process begins only after the battery has cooled down sufficiently. 2 3 ....... 1 A short beep The acoustic signal works as it should. 2 Four long beeps The battery's charge is low. Recharge the battery. 3 Rapid succession of short beeps There is a malfunction in the battery. The signal stops automatically after a few seconds. Do not attempt to charge, use or store the battery. Replace the battery. These LEDs can glow or flash green or red. If one LED glows red continuously: the battery is either too hot or too cold. Allow the battery to warm up or cool down gradually at an ambient temperature of about 50 °F to 68 °F (10 °C to 20 °C). 0458-794-8621-C 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
0458-794-8621-C
11
English
9 LED Diagnostics and Acoustic Signals
AP Adapter. Never use a wet charger,
@
5.1. Follow all
product-specific warnings and instructions accompanying
your charger.
To charge the battery:
►
Push the plug of the connecting cord (1) into the
socket (2) of the AP Adapter (3) until it stops.
►
Push the AP Adapter into the charger (5) until it stops.
The LED on the
charger
(4) glows green when the battery
is charging.
The LEDs on the
AR battery
glow green and show the
state of charge.
When the LEDs on the battery turn off, the charging
process is complete and the charger will shut itself off.
►
Remove the AP Adapter from the charger and disconnect
the charger's power supply cord from the electrical outlet
when charging is complete.
A battery is not fully charged when it ships from the factory.
STIHL recommends that you fully charge the backpack
battery before using it the first time.
Operate the charger only indoors, in dry rooms and within an
ambient temperature range of 41 °F to 104 °F (5 °C to
40 °C).
The battery heats up during operation of the power tool. If a
hot battery is connected to the charger, it may be necessary
for it to cool down before charging starts. The charging
process begins only after the battery has cooled down
sufficiently.
Charging time depends on a number of factors, including
battery condition and the ambient temperature. For a
complete list of approximate charging times, see
www.stihl.com/charging-times.
9.1
Battery Status
Six LEDs and an acoustic signal indicate the status of the
battery.
1
A short beep
The acoustic signal works as it should.
2
Four long beeps
The battery's charge is low. Recharge the battery.
3
Rapid succession of short beeps
There is a malfunction in the battery. The signal stops
automatically after a few seconds. Do not attempt to
charge, use or store the battery. Replace the battery.
These LEDs can glow or flash green or red.
3
2
1
0000-GXX-2680-A0
3
4
5
9
LED Diagnostics and Acoustic Signals
If one LED glows red continuously:
the battery is
either too hot or too cold. Allow the battery to
warm up or cool down gradually at an ambient
temperature of about 50 °F to 68 °F (10 °C to
20 °C).
1
2
3
.......
0000-GXX-3229-A1