Stihl MS 180 Product Instruction Manual - Page 45

Storing the Machine

Get Stihl MS 180 PDF manuals and user guides View all Stihl MS 180 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Checking the Spark Plug English Storing the Machine A N Clean dirty spark plug. N Check electrode gap (A) and readjust if necessary - see "Specifications." N Use only resistor type spark plugs of the approved range. Rectify problems that have caused fouling of spark plug: - too much oil in fuel mix, - dirty air filter, - unfavorable running conditions, e.g. operating at part load. 000BA039 KN 000BA071 KN 1 2 WARNING To reduce the risk of fire and burn injury, use only spark plugs authorized by STIHL. Always press spark plug boot (1) snugly onto spark plug terminal (2) of the proper size. (Note: If terminal has detachable SAE adapter nut, it must be securely attached.) A loose connection between spark plug boot and ignition wire connector in the boot may create arcing that could ignite combustible fumes and cause a fire. Installing the spark plug For periods of 3 months or longer N Drain and clean the fuel tank in a well ventilated area. N Dispose of fuel properly in accordance with local environmental requirements. N Run the engine until the carburetor is dry - this helps prevent the carburetor diaphragms sticking together. N Remove the saw chain and guide bar, clean them and spray with corrosion inhibiting oil. N Thoroughly clean the machine - pay special attention to the cylinder fins and air filter. N If you use a biological chain and bar lubricant, e.g. STIHL BioPlus, completely fill the chain oil tank. N Store the machine in a dry, high or locked location, out of the reach of children and other unauthorized persons. N Install the spark plug and connect the spark plug boot (press it down firmly) - reassembly all other parts in the reverse sequence. MS 170, MS 170 C, MS 180, MS 180 C 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
MS 170, MS 170 C, MS 180, MS 180 C
English
43
Checking the Spark Plug
N
Clean dirty spark plug.
N
Check electrode gap (A) and
readjust if necessary – see
"Specifications."
N
Use only resistor type spark plugs of
the approved range.
Rectify problems that have caused
fouling of spark plug:
–
too much oil in fuel mix,
–
dirty air filter,
–
unfavorable running conditions, e.g.
operating at part load.
WARNING
To reduce the risk of fire and burn injury,
use only spark plugs authorized by
STIHL. Always press spark plug boot (1)
snugly onto spark plug terminal (2) of the
proper size. (Note: If terminal has
detachable SAE adapter nut, it must be
securely attached.) A loose connection
between spark plug boot and ignition
wire connector in the boot may create
arcing that could ignite combustible
fumes and cause a fire.
Installing the spark plug
N
Install the spark plug and connect
the spark plug boot (press it down
firmly) – reassembly all other parts
in the reverse sequence.
For periods of 3 months or longer
N
Drain and clean the fuel tank in a
well ventilated area.
N
Dispose of fuel properly in
accordance with local
environmental requirements.
N
Run the engine until the carburetor
is dry – this helps prevent the
carburetor diaphragms sticking
together.
N
Remove the saw chain and guide
bar, clean them and spray with
corrosion inhibiting oil.
N
Thoroughly clean the machine – pay
special attention to the cylinder fins
and air filter.
N
If you use a biological chain and bar
lubricant, e.g. STIHL BioPlus,
completely fill the chain oil tank.
N
Store the machine in a dry, high or
locked location, out of the reach of
children and other unauthorized
persons.
000BA039 KN
A
1
2
000BA071 KN
Storing the Machine