Stihl MS 201 T C-M Instruction Manual - Page 12

Cutting Attachment

Get Stihl MS 201 T C-M PDF manuals and user guides View all Stihl MS 201 T C-M manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

001BA191 KN English To reduce the risk of fire and damage to hearing, do not operate your machine if the muffler is damaged or missing. - Do not touch a hot muffler since burn injury will result. Vibration behavior is influenced by the condition of the AV elements - check the AV elements at regular intervals. Check the chain catcher and replace it if damaged. Stopping the Engine - before checking chain tension. - before retensioning the chain. - before replacing the chain. - before rectifying problems. Observe sharpening instructions - keep the chain and guide bar in good condition at all times for safe and correct handling of the saw. The chain must be properly sharpened, tensioned and well lubricated. Always change the chain, guide bar and sprocket in good time. Check condition of clutch drum periodically. Store fuel and chain lubricant in properly labelled, safety-type canisters only. When handling gasoline, avoid direct contact with the skin and avoid inhaling fuel vapour - health risk. To reduce the risk of injury, shut off the engine immediately if the chain brake malfunctions - contact your servicing dealer - do not use your power tool until the problem has been rectified (see "Chain Brake"). Maintenance, replacement, or repair of the emission control devices and systems may be performed by any nonroad engine repair establishment or individual. However, if you make a warranty claim for a component which has not been serviced or maintained properly or if nonapproved replacement parts were used, STIHL may deny coverage. For any maintenance please refer to the maintenance chart and to the warranty statement near the end of the instruction manual. Cutting Attachment STIHL is the only manufacturer in the industry to produce its own chain saws, guide bars, saw chains and chain sprockets. A cutting attachment consists of the saw chain, guide bar and chain sprocket. The cutting attachment that comes standard is designed to exactly match the chain saw. 1 2 a 3 t = a : 2 - The pitch (t) of the saw chain (1), chain sprocket and the nose sprocket of the Rollomatic guide bar must match. - The drive link gauge (2) of the saw chain (1) must match the groove width of the guide bar (3). If non-matching components are used, the cutting attachment may be damaged beyond repair after a short period of operation. 10 MS 201 T

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
MS 201 T
English
10
To reduce the
risk of fire and damage to
hearing
, do not operate your machine if
the muffler is damaged or missing. –
Do not touch a hot muffler since
burn
injury
will result.
Vibration behavior is influenced by the
condition of the AV elements – check the
AV elements at regular intervals.
Check the chain catcher
and replace it if
damaged.
Stopping the Engine
–
before checking chain tension.
–
before retensioning the chain.
–
before replacing the chain.
–
before rectifying problems.
Observe sharpening instructions
– keep
the chain and guide bar in good
condition at all times for safe and correct
handling of the saw. The chain must be
properly sharpened, tensioned and well
lubricated.
Always change the chain, guide bar and
sprocket in good time.
Check condition of clutch drum
periodically.
Store fuel and chain lubricant in properly
labelled, safety-type canisters only.
When handling gasoline, avoid direct
contact with the skin and avoid inhaling
fuel vapour –
health risk.
To reduce the risk of injury, shut off the
engine immediately if the chain brake
malfunctions – contact your servicing
dealer – do not use your power tool until
the problem has been rectified (see
"Chain Brake").
Maintenance, replacement, or repair of
the emission control devices and
systems may be performed by any
nonroad engine repair establishment or
individual. However, if you make a
warranty claim for a component which
has not been serviced or maintained
properly or if nonapproved replacement
parts were used, STIHL may deny
coverage.
For any maintenance please refer to the
maintenance chart and to the warranty
statement near the end of the instruction
manual.
STIHL is the only manufacturer in the
industry to produce its own chain saws,
guide bars, saw chains and chain
sprockets.
A cutting attachment consists of the saw
chain, guide bar and chain sprocket.
The cutting attachment that comes
standard is designed to exactly match
the chain saw.
–
The pitch (t) of the saw chain (1),
chain sprocket and the nose
sprocket of the Rollomatic guide bar
must match.
–
The drive link gauge (2) of the saw
chain (1) must match the groove
width of the guide bar (3).
If non-matching components are used,
the cutting attachment may be damaged
beyond repair after a short period of
operation.
Cutting Attachment
001BA191 KN
1
2
3
a
t = a : 2