Stihl MS 360 C Instruction Manual - Page 45

Motor Management, Adjusting the Carburetor, General Information

Get Stihl MS 360 C PDF manuals and user guides View all Stihl MS 360 C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

english / USA 6 5 Motor Management Adjusting the Carburetor Exhaust emissions are controlled by the design of the fundamental engine parameters and components (e.g. carburation, ignition, timing and valve or port timing) without the addition of any major hardware. General Information The carburetor comes from the factory with a standard setting. This setting provides an optimum fuel-air mixture under most operating conditions. With this carburetor it is only possible to adjust the engine idle speed within fine limits. 138BA003K : Remove the foam filter element (5) from the front half (6) and clean or replace as necessary. : Knock the two halves of filter out on the palm of your hand or blow them clear with compressed air from the inside outwards. In case of stubborn dirt: : Wash the filter components in STIHL universal cleaner or a clean, non-flammable solution (e.g. warm soapy water) and then dry. Do not use a brush to clean the fleece filter. : Always replace a damaged filter element. : Reinstall the air filter. 44 MS 360 C

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
44
english / USA
MS 360 C
:
Remove the foam filter element
(5)
from the front half
(6)
and clean or
replace as necessary.
:
Knock the two halves of filter out on
the palm of your hand or blow them
clear with compressed air from the
inside outwards.
In case of stubborn dirt:
:
Wash the filter components in
STIHL universal cleaner or a clean,
non-flammable solution (e.g. warm
soapy water) and then dry.
Do not use a brush to clean the fleece
filter.
:
Always replace a damaged filter
element.
:
Reinstall the air filter.
Exhaust emissions are controlled by the
design of the fundamental engine
parameters and components (e.g.
carburation, ignition, timing and valve or
port timing) without the addition of any
major hardware.
General Information
The carburetor comes from the factory
with a standard setting.
This setting provides an optimum fuel-air
mixture under most operating
conditions.
With this carburetor it is only possible to
adjust the engine idle speed within fine
limits.
6
5
138BA003K
Motor Management
Adjusting the Carburetor