Symphonic CSC313E Owner's Manual - Page 13

3 After scanning The tuner stops on the lowest memorized channel. NOTES: • If there is no TV signal input, "NO TV SIGNALS" will appear on the display after the completion of channel scanning. • The unit may recognize TV channels to be CATV channels if reception condition is poor. In this case, check the antenna connection and try "AUTO CH PROGRAMMING" again when reception conditions are better. • Channel memory programming is NOT neces- sary when connected to a cable box or satellite box. Just select the channel for the cable box or satellite input (ex. CH3) on the unit, then select your desired channel on the cable box or satellite box. ADDING/DELETING CHANNELS The channels you no longer receive or seldom watch can be deleted from the memory. (Of course, you can add the deleted channel into the memory again.) 1 Select "CHANNEL SET UP" Press [MENU]. Press [PLAY/K] or [STOP/L] to point to "CHANNEL SET UP", then press [F.FWD/ B]. 2 Select "ADD/DELETE CH" Press [PLAY/K] or [STOP/L] to point to "ADD/DELETE CH", then press [F.FWD/ B]. - M E N U - TIMER PROGRAMMING PICTURE CONTROL SETTING CLOCK B CHANNEL SET UP USER'S SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] ZERO RETURN TIME SEARCH - CHANNEL SET UP - B ADD / DELETE CH (CATV) AUTO CH PROGRAMMING 3 Enter the desired channel number Press [PLAY/K] or [STOP/L] or the Number buttons until your desired channel number appears. 08 (You can also press [CHANNEL K/L] to enter it.) ADD / DELETE • You must precede single-digit (Example: CH8) channel numbers with a zero (example: 02 ... 09). • When selecting cable channels which are higher than 99, press [+100] first, then press the last two digits. (Example: to select channel 125, first press [+100] then press [2] and [5].) 4 Delete (or add) it from (or into) memory Press [REW/s] or [F.FWD/B]. The channel number changes to light red. The channel is deleted from memory. • To delete another channel, repeat steps 3 to 4. • If you press [REW/s] or [F.FWD/ B] again, the channel is memorized again. Added channel: Light blue Deleted channel: Light red 5 Exit the channel setup mode Press [MENU] to return to TV mode. NOTE: • To confirm that channel(s) has been deleted or added, press [CHANNEL K/L]. CLOCK SET UP (AUTO / MANUAL) The unit clock must be set correctly so that VCR timer recording is possible. It is suggested that the clock be set manually when first setting up the unit, then set to [ON] the auto clock setting which will periodically correct the setting if necessary. NOTE: • If you cannot receive a station with time signals, auto clock setting cannot be performed. Use manual setting only. MANUAL CLOCK SETTING Make sure ... • The unit must be turned on. In the example below, the clock is to be set to: DATE May 5th, 2005 SETTING TIME 5:40PM 1 Select "SETTING CLOCK" Press [MENU]. Press [PLAY/K] or [STOP/L] to point to "SETTING CLOCK", then press [F.FWD/ B]. - M E N U - TIMER PROGRAMMING PICTURE CONTROL B SETTING CLOCK CHANNEL SET UP USER'S SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] ZERO RETURN TIME SEARCH 2 Select "MANUAL CLOCK SET" Press [PLAY/K] or [STOP/L] to point to "MANUAL CLOCK SET", then press [F.FWD/ B]. - SETTING CLOCK - AUTO CLOCK [ON] AUTO CLOCK CH SEARCH AUTO CLOCK CH [ 02 ] B MANUAL CLOCK SET D.S.T. [OFF] 3 Select the month Press [PLAY/K] or [STOP/L] until your desired month appears. (Example: May → "05") Then press [F.FWD/ B]. - MANUAL CLOCK SET - MONTH DAY YEAR 05 HOUR MINUTE -- : -- -- 4 Select the day Press [PLAY/K] or [STOP/L] until your desired day appears. (Example: 5th → "05") Then press [F.FWD/ B]. - MANUAL CLOCK SET - MONTH DAY YEAR 05 / 05 --- ---- HOUR MINUTE -- : -- -- 5 Select the year Press [PLAY/K] or [STOP/L] until your desired year appears. (Example: "2005") Then press [F.FWD/ B]. - MANUAL CLOCK SET - MONTH DAY YEAR 0 5 / 0 5 THU 2 0 0 5 HOUR MINUTE -- : -- -- - 13 - EN