Symphonic RSMSD804 Owner's Manual - Page 27

1 Connections Please refer to "Basic TV Connection" on the front page before you use this unit. RF Output Channel If channel 3 is already occupied for broadcasting, 1)Set your TV to channel 4. 2)Insert a pre-recorded tape into this unit. 3)Press the OUTPUT button on the DVD/VCR so that the VCR OUTPUT light is lit. • If noise appears on the TV screen, press the VCR/TV button on the remote control. 4)Press the PLAY button once. 5)After a few seconds, press the PLAY button on the DVD/VCR for 3 seconds. • The RF output channel will change to channel 4 from channel 3 and you will see a playback picture. • When a picture does not appear on the TV screen, repeat step [4]. 6)Press the STOP button to stop playback. 2 Installing the Batteries for the Remote Control 1 2 3 3 VCR/DVD Switching POWER POWER ON VIDEO AUDIO REC TIMER REC REW F.FWD STOP/EJECT PLAY REC/OTR VCR OPEN CLOSE CHANNEL VCR DVD DISC IN PLAY OUTPUT SELECT REV/SKIP STOP PLAY SKIP/FWD VCR button DVD button DVD DVD OUTPUT light SUBTITLE/ TIMER SET POWER SETUP AUDIO V.SURR ANGLE REC/OTR REPEAT SKIP/ CH TOP MENU C-RESET CLEAR MODE REPEAT A-B SKIIP/ CH RETURN DISPLAY VCR DVD MENU ENTER STOP PLAY OUTPUT SELECT VCR OUTPUT light OUTPUT button NA509 1 4 7 +10 PAUSE SPEED 23 SLOW 56 VCR/TV 89 SEARCH MODE 0 Quick Use Guide 4 Turn on the unit for the first time VCR VCR 1 Turn on the TV and set it to channel 3. • If channel 3 is already occupied for broadcasting, see"RF Output Channel" section. 2 POWER Remote Control TV Screen LANGUAGE SELECT B ENGLISH [ON] or FRANCAIS ESPAÑOL 3 CH 01 AUTO SET UP Do you connect the cable from the cable box or the satellite box to the DVD/VCR's ANT IN jack? YES Yes Press the MENU button to exit NO No Please wait for a few minutes. After scanning... • The tuner stops on the lowest memorized channel. • You can select only the channels memorized in this unit by using the CHANNEL buttons. VCR MODE Press the VCR button on the remote control. (Verify that the VCR OUTPUT light is lit.) DVD MODE Press the DVD button on the remote control. (Verify that the DVD OUTPUT light is lit.) Note • Pressing only the OUTPUT button on the front panel DOES NOT switch the mode of the remote control. You MUST select the correct mode on the remote control. 5 Clock Set Up VCR 1 MENU VCR -MENU- TIMER PROGRAMMING AUTO REPEAT [OFF] CHANNEL SET UP B CLOCK SET LANGUAGE SELECT or • If the clock is not set, the CLOCK SET screen appears when you press the MENU button. In this case, go to step [2]. 2 or 3 or 4 or 5 or 6 or CLOCK SET MONTH DAY 03 / -- YEAR - - - - HOUR MINUTE AM/PM -- : -- - - Select the current month CLOCK SET MONTH DAY 03 / 15 YEAR - - - - HOUR MINUTE AM/PM -- : -- - - Select the current day CLOCK SET MONTH DAY 03 / 15 YEAR 2 0 0 4 HOUR MINUTE AM/PM -- : -- - - Select the current year CLOCK SET MONTH DAY YEAR 0 3 / 1 5 MON 2 0 0 4 HOUR MINUTE AM/PM 05 : -- - - Select the current hour CLOCK SET MONTH DAY YEAR 0 3 / 1 5 MON 2 0 0 4 HOUR MINUTE AM/PM 05 : 40 - - Select the current minute 7 or CLOCK SET MONTH DAY YEAR 0 3 / 1 5 MON 2 0 0 4 HOUR MINUTE AM/PM 05 : 40 P M AM B PM Select "AM" or "PM" 8 To exit the CLOCK SET screen. ✄ - 27 - EN