Symphonic RSMWD2205 Owner's Manual - Page 27

Quick Use Guide 1 Connections Please refer to "Basic TV Connection" on the front page before you use this unit. RF Output Channel If channel 3 is already occupied for broadcasting, 1)Set your TV to channel 4. 2)Insert a pre-recorded tape into this unit. 3)Hit [SOURCE] on the unit so that the VCR OUTPUT light is lit. • If "VCR" light does not appear on the display of this unit, hit [VCR/TV] on the remote control. 4)Hit [PLAY B] once. 5)After a few seconds, hit [PLAY B] on the unit for 3 seconds. • The RF output channel will change to channel 4 from channel 3 and you will see a playback picture. • When a picture does not appear on the TV screen, repeat step 4). 6)Hit [STOP C] to stop playback. 2 Installing the Batteries for the Remote Control 1 2 3 3 VCR/DVD Switching X Y X Y VIDEO y E D C A REC B TIMER STANDBY-ON REW F.FWD STOP/EJECT PLAY RECORD IR AUDIO VCR YX CHANNEL A OPEN/ CLOSE VCR DVD DISC IN PLAY H SOURCE PREV C STOP B PLAY G NEXT VCR button DVD button DVD OPEN/CLOSE STANDBY-ON SPEED AUDIO /EJECT 12 45 78 0 DISPLAY VCR 3 SKIP/CH. 6 VCR/TV 9 SLOW +10 DVD PAUSE RECORD PLAY STOP SOURCE DVD OUTPUT light PREV SOURCE button VCR OUTPUT light MENU ENTER SETUP TOP MENU RETURN MODE ZOOM SEARCH MODE CLEAR/ C. RESET SUBTITLE T-SET ANGLE REPEAT A-B VCR MODE Hit [VCR] on the remote control. (Verify that the VCR OUTPUT light is lit.) 4 Turn on the unit for the first time VCR VCR 1 Turn on the TV and set it to channel 3. • If channel 3 is already occupied for broadcasting, see"RF Output Channel" section. 2 STANBY-ON Remote Control TV Screen LANGUAGE SELECT B ENGLISH [ON] FRANÇAIS or ESPAÑOL 3 CH 01 AUTO SET UP Do you connect the cable from the cable box or the satellite box to the unit's ANT-IN jack? YES Yes Hit MENU to exit. NO No Please wait for a few minutes. After scanning... • The tuner stops on the lowest memorized channel. • You can select only the channels memorized in this unit by using [SKIP/CH. G/K H/L] (or [CHANNEL K/L]). • If "AUTO SET UP" appears on the TV screen again, check the cable connections. Then, hit [B] once again. 5 Clock Set Up VCR 1 MENU VCR - M E N U - TIMER PROGRAMMING AUTO REPEAT [OFF] CHANNEL SET UP B CLOCK SET LANGUAGE SELECT • If the clock is not set, the or CLOCK SET screen appears when you hit [MENU]. In this case, go to step 2). 2 or 3 or 4 or 5 or 6 or CLOCK SET MONTH DAY 10 / -- YEAR - - - - HOUR MINUTE AM/PM -- : -- - - Select the current month. CLOCK SET MONTH DAY 10 / 03 YEAR - - - - HOUR MINUTE AM/PM -- : -- - - Select the current day. CLOCK SET MONTH DAY 10 / 03 YEAR 2 0 0 5 HOUR MINUTE AM/PM -- : -- - - Select the current year. CLOCK SET MONTH DAY YEAR 1 0 / 0 3 MON 2 0 0 5 HOUR MINUTE AM/PM 05 : -- - - Select the current hour. CLOCK SET MONTH DAY YEAR 1 0 / 0 3 MON 2 0 0 5 HOUR MINUTE AM/PM 05 : 40 - - Select the current minute. DVD MODE Hit [DVD] on the remote control. (Verify that the DVD OUTPUT light is lit.) Hint • Hitting only [SOURCE] on the front panel DOES NOT switch the mode of the remote control. You MUST select the correct mode on the remote control. 7 or CLOCK SET MONTH DAY YEAR 1 0 / 0 3 MON 2 0 0 5 HOUR MINUTE AM/PM 05 : 40 P M AM B PM Select "AM" or "PM". 8 To exit the CLOCK SET screen ✄ - 27 - EN